VOLVO TRUCK FH MK I VERSION 98 340 12L 250kW/335HP LUCAS

Centralita LUCAS PLCC 28HC256 · 340 CV (25 kW) · 12000 cc · Diesel sovralimentato

Base de datos de centralitasVOLVO TRUCK › VOLVO TRUCK FH MK I VERSION 98 340 12L 250kW/335HP LUCAS

Encuentra los identificadores del firmware (hardware, software y actualización), las opciones de tuning disponibles y cómo obtener el archivo original o remapeado.

✓ Tuning por archivo (flash) 12 versiones de firmware

Datos del vehículo

MarcaVOLVO TRUCK
ModeloFH MK I VERSION 98
Motor340 12L 250kW/335HP LUCAS
Potencia de serie340 CV / 25 kW
Cilindrada12000 cc
CombustibleDiesel sovralimentato
Tipo de vehículoTir

Centralita

FabricanteLUCAS
ModeloPLCC 28HC256
Memoria / EPROM28HC256 PLCC32 256Kbit - EEprom 32K x 8

Operaciones / opciones de tuning disponibles:

  • Inyección al ralentí
  • Inyección a carga parcial
  • Inyección a plena carga
  • Limitador de carga 2
  • Limitador de carga
  • Limitador de gases al ralentí
  • Limitador de gases a carga parcial
  • Limitador de gases a plena carga

Identificadores de firmware (12)

N.º HardwareN.º Software (chip)VersiónSoftware de actualizaciónCentralita
03161952XXXX3237 1.55.004 LUCAS PLCC 28HC256
03161952XXXX3190 1.55.002 LUCAS PLCC 28HC256
03161962XXXX6230 1.55.004 LUCAS PLCC 28HC256
03161962XXXX4922 1.55.003 LUCAS PLCC 28HC256
03161962XXXX4747 1.55.005 LUCAS PLCC 28HC256
08170700XXXX3218 1.55.004 LUCAS PLCC 28HC256
08170700XXXX3190 1.55.003 LUCAS PLCC 28HC256
08170700XXXX3083 1.55.116 LUCAS PLCC 28HC256
20412506XXXX3337 1.55.003 LUCAS PLCC 28HC256
20577131XXXX3296 1.55.003 LUCAS PLCC 28HC256
20577131XXXX1481 1.55.005 LUCAS PLCC 28HC256
20582958XXXX4638 1.55.003 LUCAS PLCC 28HC256

Notas de la centralita

Original EPROM 28HC256 PLCC 32 pins This Setting File can be used for serial system NewGenius. To read this EPROM with the EMP20 programmer you need PD28 adapters. Attention !! The EMP21 instead needs the PD32 adapters. WARNING !! With the eprom programmer EMP21 at first select device, then choose "DEVICE OPTIONS" and then "DISABLE SDP AFTER PROGRAM" (confirm with "OK"). With EMP20 once the eprom has been programmed, select "B" for disable data protection and confirm with "Y". On this epron can be set a KEY.
Original EPROM 28HC256 PLCC 32 pins To read this EPROM with the EMP20 programmer you need PD28 adapters. Attention !! The EMP21 instead needs the PD32 adapters. On this epron can be set a KEY. WARNING !! With the eprom programmer EMP21 at first select device, then choose "DEVICE OPTIONS" and then "DISABLE SDP AFTER PROGRAM" (confirm with "OK"). With EMP20 once the eprom has been programmed, select "B" for disable data protection and confirm with "Y". This Setting File can be used for serial system NewGenius.