English English Español Español Italiano Italiano Nederlands Nederlands Deutsch Deutsch 中文 中文 Français Français Lietuvių Lietuvių

CAN-AM/BRP MAVERICK X3-R 900 19->21 113kW

ECU BOSCH ME17.8.5 · 154 CV (113 kW) · 900 cc · Benzina sovralimentato

ECU Database › CAN-AM/BRP › CAN-AM/BRP MAVERICK X3-R 900 19->21 113kW

Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.

✓ Tuning via file (flash) 2 firmware versions

Get the file for this vehicle

Buy the file (original or remapped)Register on mastertuningfile.com and order the file

Are you a workshop or tuner?

Vehicle data

BrandCAN-AM/BRP
ModelMAVERICK X3-R 900
Engine19->21 113kW
Stock power154 CV / 113 kW
Displacement900 cc
FuelBenzina sovralimentato
Vehicle typeMoto

ECU

ManufacturerBOSCH
ModelME17.8.5
Memory / EPROMMICRO ST TRICORE - 12032 Kbit - 178000

Available tuning operations / options:

  • Base timing
  • Lambda/AFR mixture for engine temperature at crancking
  • Optimal spark timing/MBT
  • Boost pressure limit control
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Compression ratio for turbocharger protection
  • Desired pressure ratio
  • Exhaust gas temperature
  • Expected vehicle speed
  • ECT for fan disengagement
  • ECT for fan engagement
  • INJLC
  • Injector latency - cylinder 2
  • INJSC
  • Injector scaling - cylinder 2
  • Torque limiter
  • Lambda enrichment for components protection
  • RPM Limiter
  • RPM Limiter 2
  • Gear dependent maximum engine speed
  • RPM limiter in limp mode
  • Maximum limitation Lambda sensor
  • Speed limiter based on gear
  • Speed limiter for key
  • Speed limiter - rear axle protection
  • Speed limiter for unknown gear
  • Map sensor offset
  • MAP sensor slope
  • Max MAP sensor voltage
  • Throttle air mass flow calculation
  • Min MAP sensor voltage
  • Max allowed torque for speed limit control
  • Optimal engine moment
  • RPM hysteresis above rev limit for fuel cut-off
  • Driver torque request
  • Throttle angle management
  • Torque limit table for IAT sensor
  • Torque limit for voltage
  • Target Lambda for knock protection
  • Torque limit table for ECT sensor
  • Volumetric efficiency
  • RPM threshold for 2 foot
  • Vehicle speed threshold for 2 foot
  • WG duty cycle vs RPM and boost

Firmware identifiers (2)

Hardware No.Software No. (chip)VersionUpdate softwareECU
F00HM001967E2159NE0VLS2 1.94.021— BOSCH ME17.8.5
F00HM001967E2159NE0VLS3 1.94.014— BOSCH ME17.8.5

ECU notes

MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata

Get the file for this vehicle

Buy the file (original or remapped)Register on mastertuningfile.com and order the file Are you a workshop or tuner?Offer these services yourself: activate your TuningFile platform

Tools to read and write this ECU

Flex Programmatore per rimappatura centraline e cambi automatici Flex Programmatore per rimappatura centraline e cambi automatici ECU + auto gearbox € 1.000 Buy The Genius The Genius OBD + Bench € 2.500 Buy

Other CAN-AM/BRP

OUTLANDER XT 800
09->14 50kW COMMANDER 1000
18->20 66kW OUTLANDER 570
16->25 36kW MAVERICK 1000
16->20 75kW RENEGADE 800
09->14 54kW RENEGADE 1000
15->17 66kW COMMANDER 800
18->20 53kW MAVERICK Xds 1000
16->19 88kW OUTLANDER XT 400
14->18 28kW RENEGADE 500
09->14 34kW

→ All ECUs CAN-AM/BRP