VOLKSWAGEN SCIROCCO 3 1.4L 16V TSI 118kW/158HP MED17.5

ECU BOSCH MED17.5 · 160 CV (118 kW) · 1400 cc · Benzina sovralimentato

ECU DatabaseVOLKSWAGEN › VOLKSWAGEN SCIROCCO 3 1.4L 16V TSI 118kW/158HP MED17.5

Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.

✓ Tuning via file (flash) ✓ Add-on module available 21 firmware versions

Vehicle data

BrandVOLKSWAGEN
ModelSCIROCCO 3
Engine1.4L 16V TSI 118kW/158HP MED17.5
Stock power160 CV / 118 kW
Displacement1400 cc
FuelBenzina sovralimentato
Vehicle typeAuto

ECU

ManufacturerBOSCH
ModelMED17.5
Memory / EPROMMICRO ST TRICORE - 12032 Kbit - 178000

Available tuning operations / options:

  • Base timing
  • Optimal spark timing/MBT
  • Advance correction
  • Height correction for boost pressure
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Exhaust gas temperature
  • Gearbox maximum torque allowed
  • High pressure fuel pump setpoint
  • High fuel pressure pump limit for ECT sensor
  • High fuel pressure pump limit
  • Lambda enrichment for components protection
  • Lambda correction for exhaust manifold temperature
  • Torque limiter at high EGT
  • RPM Limiter
  • Knock detection factor
  • Speed limiter
  • Speed limiter 2
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Optimal engine moment
  • Power limit torque table
  • Relative permissible torque from the pedal position in torque limitation
  • Relative permissible torque from the pedal position in torque limitation - sport/race mode
  • Pressure ratio depending on IAT
  • Driver torque request
  • Driver torque request AWD
  • Driver torque request for reverse gear
  • Exhaust gas temperature sensor
  • Throttle angle management

Firmware identifiers (21)

Hardware No.Software No. (chip)VersionUpdate softwareECU
1.94.01803C906027F 3427 BOSCH MED17.5
1.94.02003C906027F 3093 BOSCH MED17.5
1.94.02303C906027BA 5860 BOSCH MED17.5
1.94.01703C906027G 4009 BOSCH MED17.5
1.94.00803C906027BB 8902 BOSCH MED17.5
1.94.02103C906027F 4008 BOSCH MED17.5
1.94.01703C997027A 3115 BOSCH MED17.5
1.94.01203C906027J 3429 BOSCH MED17.5
1.94.01003C906026AB 3731 BOSCH MED17.5.5
1.94.01803C906027BS 0888 BOSCH MED17.5.5
1.94.01403C906027BS 0173 BOSCH MED17.5.5
1.94.00603C906027CT 0175 BOSCH MED17.5.5
1.94.02003C906026AA 3730 BOSCH MED17.5.5
1.94.02203C906027CN 2535 BOSCH MED17.5.5
1.94.01203C906026B 3721 BOSCH MED17.5.5
1.94.03103C906027BA 8913 BOSCH MED17.5.5
1.94.02603C906027BA 9660 BOSCH MED17.5.5
1.94.04303C906027BS 1676 BOSCH MED17.5.5
1.94.02103C906027AT 5859 BOSCH MED17.5.5
1.94.00403C906026AA 6141 BOSCH MED17.5.5
1.94.00603C906027CT 1678 BOSCH MED17.5.5

ECU notes

MICRO Infineon Tricore TC1766 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1767 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata

Add-on modules available

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

→ See all add-on modules on the shop