Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.
✓ Tuning via file (flash)
1 firmware versions
Vehicle data
| Brand | PORSCHE |
| Model | PANAMERA (971) |
| Engine | 4.0L V8 32V 463kW/630HP MG1CS008 |
| Stock power | 630 CV / 463 kW |
| Displacement | 4000 cc |
| Fuel | Benzina sovralimentato |
| Vehicle type | Auto |
ECU
| Manufacturer | BOSCH |
| Model | MG1CS008 |
| Memory / EPROM | Micro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte |
Available tuning operations / options:
- Absolute boost limit
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Advance at idle speed
- Minimum advance allowed
- Optimal spark timing/MBT
- Optimal spark timing/MBT 2
- Boost pressure limiter
- Lambda correction for engine temperature after starting
- Driver torque limit for clutch protection
- Compression ratio for turbocharger protection
- Compression ratio limiting for compressor depending on IAT sensor
- Max accepted exhaust gas temperature at exhaust manifold
- Exhaust gas temperature
- Exhaust gas temperature 2
- Exhaust valves lift
- Characteristic line correction factor for pressure ratio for turbocharger overspeed protection
- Characteristic line correction factor for pressure ratio for turbocharger overspeed protection 2
- Boost pressure preload correction factor
- Boost pressure preload correction factor 3
- Factor for reducing maximum filling
- Engine torque reducing factor depending on temperature
- Engine idle vs. ECT sensor
- Gearbox maximum torque allowed
- Boost pressure control hysteresis
- HFM/HLM air flow high limit
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- High fuel pressure pump limit
- Intake valve lift
- Torque limiter 2
- L
- Advance limiter for component protection 1
- Boost pressure deviation limits for basic charge air pressure
- Boost pressure deviation limits for basic charge air pressure 2
- Torque limiter
- Torque limiter for electrical engine
- Torque limiter for electrical engine Sport mode
- Lambda enrichment for components protection
- Component protection activation delay
- Lambda minimum value for components protection
- Lambda value for components protection activation
- Lambda correction for exhaust manifold temperature
- RPM Limiter
- RPM Limiter 2
- RPM limiter - N
- RPM limiter in Park position
- Engine speed limit temperature based
- RPM limit for ECT sensor
- RPM limit for EOT sensor
- Lambda driver wish
- Knock detection factor
- Speed limiter
- Maximum indicated torque
- Maximum indicated torque for monitoring
- Maximum engine torque at crank shaft
- Maximum engine load based on exhaust back pressure
- Maximum engine load in case of exhaust valve error
- Maximum engine load in case of turbocharger error
- Maximum engine temperature for torque limitation
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Maximum intake manifold pressure
- Maximum throttle angle opening for a given RPM
- Max torque profile
- Max wastegate dutycycle
- Optimal engine moment
- Optimal engine moment 2
- Power limit torque table
- % relative air filling limit depending on IAT
- Driver torque request
- Driver torque request 2
- Driver torque request 3
- Compressor surge line definition
- Target Lambda for knock protection
- Torque limiter in recovery mode
- Torque limiter in recovery mode 2
- Torque limiter in recovery mode 3
- Torque limiter in recovery mode 4
- Torque limiter in recovery mode 5
- Minimum engine rpm threshold for diagnosis
- Minimum engine rpm threshold for diagnosis 2
- Turbocharger volumetric efficiency
Firmware identifiers (1)
| Hardware No. | Software No. (chip) | Version | Update software | ECU |
| — | — |
1.02.018 | 971906014AD 0003 |
BOSCH MG1CS008 |
ECU notes
Microprocessor BGA FREESCALE SPC57xxx This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Get the file for this vehicle
Tools to read and write this ECU