Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.
✓ Tuning via file (flash)
✓ Add-on module available 9 firmware versions
Vehicle data
| Brand | MITSUBISHI |
| Model | OUTLANDER MK2 |
| Engine | 2.0L DI-D 100kW/136HP EDC16+ |
| Stock power | 136 CV / 1 kW |
| Displacement | 2000 cc |
| Fuel | Diesel sovralimentato |
| Vehicle type | Auto |
ECU
| Manufacturer | BOSCH |
| Model | EDC16U31 |
| Memory / EPROM | M58BW016DB PQFP80 - Flash 3_V 512 x 32 |
Available tuning operations / options:
- Smoke limiter 2
- Main injection duration angle
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure 2
- Boost pressure in aftertreatment modes
- Boost pressure in aftertreatment modes 2
- EGR valve control
- EGR valve control 2
- EGR valve control 3
- EGR valve control in aftertreatment modes
- EGR valve control in aftertreatment modes 2
- Exhaust gas temperature
- Exhaust gas temperature 2
- Protection for engine overheating
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Gearbox maximum torque allowed
- Injection period
- Injection period - correction
- Maximum injection period
- Max injection limit - limp mode
- Injection 1
- Injection in aftertreatment modes 1
- L
- Torque limiter
- Smoke limiter
- RPM limiter - fuel cut
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation in aftertreatment modes
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature for O2
- LSU temperature threshold PID heater governor activation
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Air mass flow
- Driver torque request
- Driver torque request 2
- CAT downstream temperature sensor characterization
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for selected gear
- Torque limiter for for reverse gear
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Torque limiter in recovery mode 2
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
Firmware identifiers (9)
| Hardware No. | Software No. (chip) | Version | Update software | ECU |
|---|
| — | 1037390125 |
1.67.022 | 1037390125 |
BOSCH EDC16U31 |
| — | 1037384627 |
1.67.009 | 1037393542 |
BOSCH EDC16U31 |
| — | 1037384821 |
1.67.024 | 1037384821 |
BOSCH EDC16U31 |
| — | 1037384628 |
1.67.011 | 1037384821 |
BOSCH EDC16U31 |
| — | 1037393541 |
1.67.022 | 1037393541 |
BOSCH EDC16U31 |
| — | 1037390125 |
1.67.018 | 1037393541 |
BOSCH EDC16U31 |
| — | 1037384821 |
1.67.016 | 1037393541 |
BOSCH EDC16U31 |
| — | 1037384627 |
1.67.013 | 1037390124 |
BOSCH EDC16U31 |
| — | 1037384821 |
1.67.023 | 1037384821 |
BOSCH EDC16U31 |
ECU notes
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4. This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
Get the file for this vehicle
Tools to read and write this ECU
