BMW X4 SERIES G02 20i 2.0L 16V 135kW/181HP DME__84T0

ECU BOSCH MG1CS201 (DME_84T0) · 184 CV (135 kW) · 2000 cc · Benzina sovralimentato

ECU DatabaseBMW › BMW X4 SERIES G02 20i 2.0L 16V 135kW/181HP DME__84T0

Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.

✓ Tuning via file (flash) 4 firmware versions

Vehicle data

BrandBMW
ModelX4 SERIES G02
Engine20i 2.0L 16V 135kW/181HP DME__84T0
Stock power184 CV / 135 kW
Displacement2000 cc
FuelBenzina sovralimentato
Vehicle typeAuto

ECU

ManufacturerBOSCH
ModelMG1CS201 (DME_84T0)
Memory / EPROMMicro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte

Available tuning operations / options:

  • Base timing
  • Base timing 2
  • Camshaft maximum lift
  • Lambda/AFR full load/WOT
  • Lambda/AFR mixture at part load
  • Optimal spark timing/MBT
  • Optimal spark timing/MBT 2
  • Knock correction advance max
  • Boost pressure limiter for diagnostics
  • Maximum torque limitation at clutch
  • Desired pressure ratio
  • Max accepted exhaust gas temperature value after turbine
  • Max accepted exhaust gas pressure at exhaust manifold
  • Exhaust gas temperature 2
  • Exhaust gas temperature 3
  • Exhaust gas temperature 4
  • Exhaust gas temperature 5
  • Max torque correction factor for knock sensor
  • Filling factor limit
  • Filling factor limit 2
  • Filling factor limit 3
  • Filling factor limit 4
  • Engine torque reducing factor depending on engine speed
  • Engine torque reducing factor depending on temperature
  • HFM/HLM threshold for diagnosis
  • HFM/HLM air flow high limit
  • HFM/HLM air flow low limit
  • High pressure fuel pump setpoint
  • High fuel pressure pump limit for ECT sensor
  • High fuel pressure pump limit 2
  • Intake pressure protection
  • Intake valve lift - cold
  • Intake valve lift - catalyst heating
  • Intake valve lift - start for ECT sensor
  • Intake valve lift - warm
  • Torque limiter 2
  • L
  • Torque limiter 4
  • Basic value Lambda sensor
  • Torque limiter
  • Lambda minimum value for components protection
  • Lambda fat-running limit for component protection
  • RPM limiter - AT
  • RPM limiter - MT
  • Low pressure fuel pump for EFT sensor
  • Knock detection factor
  • Speed limiter
  • Maximum indicated torque
  • Maximum compression ratio
  • Maximum possible engine charge
  • Maximum engine power
  • Maximum engine pressure ratio
  • Maximum relative engine air charge
  • Max torque profile - AT
  • Max torque profile - MT
  • Optimal engine moment
  • Pressure ratio depending on IAT
  • Pressure ratio depending on IAT 2
  • Driver torque request
  • Driver torque request Eco mode - AT
  • Driver torque request Eco mode - AT - 2
  • Driver torque request Normal mode - AT
  • Driver torque request Sport mode - AT
  • Driver torque request Sport mode - AT - 2
  • Driver torque request Eco mode
  • Driver torque request Eco mode - MT
  • Driver torque request Eco mode - MT - 2
  • Driver torque request Normal mode - MT
  • Driver torque request Sport mode - MT
  • Driver torque request Sport mode - MT - 2
  • Driver torque request Sport mode
  • Torque limiter for selected gear
  • Torque limiter for selected gear - AT
  • Start of injection
  • Maximum upper tolerance intake pressure protection
  • Torque limit table for IAT sensor
  • Lower pressure control threshold
  • Torque limiter to prevent preignition
  • Torque limiter in recovery mode
  • Torque limiter in recovery mode 2
  • Upper engine rpm threshold for diagnostic control
  • Upper pressure control threshold
  • Turbocharger volumetric efficiency
  • Wastegate duty-cycle

Firmware identifiers (4)

Hardware No.Software No. (chip)VersionUpdate softwareECU
0000429501140200005D55463208 1.94.006000063CD463201 BOSCH MG1CS201 (DME_84T0)
0000429501140200005D55462805 1.94.009000063CD462806 BOSCH MG1CS201 (DME_84T0)
0000429501140200005D55463C07 1.94.00500006387463C65 BOSCH MG1CS201 (DME_84T0)
00004295012D0100005D5550480C 1.94.02600006F02504898 BOSCH MG1CS201 (DME_84T0)

ECU notes

Micro Infineon Tricore TC298TP Serial protocol enabled ONLY on New Genius, it does not work on Genius To work on this ECU you can use NewTrasdata