BMW MOTORRAD F 850 GS 18->20 70kW

ECU BOSCH ME17.2.4 BMS-MP · 95 CV (7 kW) · 800 cc · Benzina aspirato

ECU DatabaseBMW MOTORRAD › BMW MOTORRAD F 850 GS 18->20 70kW

Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.

✓ Tuning via file (flash) 21 firmware versions

Vehicle data

BrandBMW MOTORRAD
ModelF 850 GS
Engine18->20 70kW
Stock power95 CV / 7 kW
Displacement800 cc
FuelBenzina aspirato
Vehicle typeMoto

ECU

ManufacturerBOSCH
ModelME17.2.4 BMS-MP
Memory / EPROMMICRO ST TRICORE - 32768 - 400000

Available tuning operations / options:

  • Engine ignition timing versus temperature
  • Advance at idle speed
  • Lambda/AFR full load/WOT
  • Advance at idle speed - warm up
  • Optimal spark timing/MBT
  • Advance at part load
  • Advance at part load - warm up
  • Automatic stability control 1
  • Automatic stability control 2
  • Automatic stability control 3
  • Automatic stability control 4
  • Automatic stability control 5
  • Advance full load
  • Advance full load - warm up
  • Dynamic traction control
  • Dynamic traction control 2
  • Dynamic traction control 3
  • Dynamic traction control 4
  • Dynamic traction control 5
  • Exhaust valve management
  • Exhaust valve management - limiter
  • Factor to correct fuel delivery system
  • Engine torque reducing factor depending on engine speed
  • Engine idle vs. ECT sensor
  • Engine idle vs. ECT sensor 3
  • Injection correction cilinder 1
  • Injection correction cilinder 2
  • Rpm threshold fuel cut
  • Idle throttle angle correction for ECT sensor
  • Advance limiter for component protection 1
  • Advance limiter lower motor temperature threshold
  • Advance limiter upper motor temperature threshold
  • Torque limiter
  • Lambda efficiency
  • Exhaust valve opening limit
  • RPM Limiter
  • RPM Limiter 2
  • RPM Limiter for gear downshift
  • RPM limiter in limp mode
  • RPM limiter - N
  • Lambda driver wish
  • Lambda driver wish 2
  • Maximum indicated torque
  • Optimal engine moment
  • Specific injection pressure
  • Air mass flow
  • Exhaust gas temperature sensor
  • Throttle angle limitation
  • Throttle angle limitation 2
  • Throttle angle management
  • Cooling fan activation
  • Front tire circumference
  • Rear tire circumference

Firmware identifiers (21)

Hardware No.Software No. (chip)VersionUpdate softwareECU
0000306405000000003065120000 1.95.0080000432C120002 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0080000432B120000 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0080000432A120002 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0080000432B120002 BOSCH ME17.2.4 BMS-MP
00003064050000000030650E0000 1.95.0050000432D0E0009 BOSCH ME17.2.4 BMS-MP
00003064050000000030650D0000 1.95.0130000432A0D0004 BOSCH ME17.2.4 BMS-MP
0000306405000000003065110000 1.95.0130000432A110000 BOSCH ME17.2.4 BMS-MP
00003064050000000030650E0000 1.95.0070000432A0E0005 BOSCH ME17.2.4 BMS-MP
00003064050000000030650E0000 1.95.0100000432B0E0005 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0090000432D120002 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0090000432F120000 BOSCH ME17.2.4 BMS-MP
0000306405000000003065100000 1.95.0090000432A100000 BOSCH ME17.2.4 BMS-MP
0000306405000000003065110000 1.95.0060000432D110000 BOSCH ME17.2.4 BMS-MP
00003064050000000030650E0000 1.95.0060000432A0E0009 BOSCH ME17.2.4 BMS-MP
0000306405000000003065100000 1.95.0130000432B100000 BOSCH ME17.2.4 BMS-MP
0000306405000000003065100000 1.95.0090000432D100000 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0080000432D120000 BOSCH ME17.2.4 BMS-MP
00003064050000000030650E0000 1.95.007000043320E0009 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0110000432A120000 BOSCH ME17.2.4 BMS-MP
00003064050000000030650E0000 1.95.0070000432B0E0009 BOSCH ME17.2.4 BMS-MP
0000306405000000003065120000 1.95.0090000432D120001 BOSCH ME17.2.4 BMS-MP

ECU notes

MICRO Infineon Tricore TC1793 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata