Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.
✓ Tuning via file (flash)
✓ Add-on module available 2 firmware versions
Vehicle data
| Brand | AUDI |
| Model | A7 (4K8) |
| Engine | 50 3.0L V6 TDI 210kW/282HP MD1CP004 |
| Stock power | 286 CV / 21 kW |
| Displacement | 3000 cc |
| Fuel | Diesel sovralimentato |
| Vehicle type | Auto |
ECU
| Manufacturer | BOSCH |
| Model | MD1CP004 |
| Memory / EPROM | Micro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte |
Available tuning operations / options:
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure 2
- Boost pressure 3
- Boost pressure 4
- Boost pressure 5
- Boost pressure 6
- Boost pressure 7
- Boost pressure 8
- Protection for cylinder head overheating
- Maximum torque limitation at clutch
- Max accepted exhaust gas temperature value before turbine
- Max accepted exhaust gas temperature value before turbine 2
- Max accepted exhaust gas temperature value before turbine 3
- Protection for engine overheating
- Basic torque management at engine cranking
- Basic torque management at engine cranking 2
- Basic torque management at engine cranking 3
- Injection period
- Injection period 10
- Injection period 11
- IF1
- Injection period 13
- Injection period 14
- Injection period 15
- Injection period 16
- Injection period 17
- Injection period 4
- Injection period 5
- Injection period 6
- Injection period 7
- Injection period 8
- Injection period 9
- Injection period limit
- Injection period limit 2
- Injection opening time related to inj. pressure
- Injection 1
- Injection 2
- Injection 3
- J
- Torque limiter 2
- Torque limiter 3
- L
- Torque limiter 5
- Torque limiter
- Torque limiter for electrical engine
- Torque limiter with combustion engine in Lambda = 1 mode
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Lambda value of the smoke limitation 3
- Speed limiter
- Speed limiter 2
- Max torque profile - AT
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure 4
- Driver torque request
- Driver torque request 2
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Start of injection
- Start of injection 2
- Torque limiter for the APS/BPS
- Torque limiter for the APS/BPS 2
- Torque limiter in recovery mode
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
Firmware identifiers (2)
| Hardware No. | Software No. (chip) | Version | Update software | ECU |
|---|
| — | — |
1.02.010 | 4K0907401K 0003 |
BOSCH MD1CP004 |
| — | — |
1.02.013 | 4K0907401 0003 |
BOSCH MD1CP004 |
ECU notes
Micro Infineon Tricore TC298TP This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Add-on modules available
A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):
Get the file for this vehicle
Tools to read and write this ECU
