VOLVO XC70 Mk2 2.5L 20V T5 154kW/207HP ME7.0

Calculateur BOSCH ME7.0 · 209 CV (154 kW) · 2500 cc · Benzina sovralimentato

Base de données calculateursVOLVO › VOLVO XC70 Mk2 2.5L 20V T5 154kW/207HP ME7.0

Retrouvez les identifiants du firmware (numéros hardware, software et mise à jour), les options de tuning disponibles et comment obtenir le fichier d'origine ou reprogrammé.

✓ Tuning par fichier (flash) 5 versions firmware

Données véhicule

MarqueVOLVO
ModèleXC70 Mk2
Moteur2.5L 20V T5 154kW/207HP ME7.0
Puissance d'origine209 CV / 154 kW
Cylindrée2500 cc
CarburantBenzina sovralimentato
Type de véhiculeAuto

Calculateur

FabricantBOSCH
ModèleME7.0
Mémoire / EPROM29F800 PSOP44 8Mbit - Flash 512K x 16

Opérations / options de tuning disponibles:

  • Avance principale
  • Avance optimal
  • Limiteur de pression turbo
  • Controle limite de pression de turbo
  • Correction altitude pression turbo
  • Calcul de charge du moteur désirée
  • Correction lambda en fonction de la température du moteur après le début
  • Température des gaz d'échappement
  • Limiteur de tours
  • Linéarisation pression turbo
  • Lambda demandée
  • Limiteur de vitesse
  • Charge maximale de la pression de suralimentation
  • Calcul du débit massique d'air d'accélérateur
  • Couple optimal du moteur
  • Demande de couple
  • Gestion angle papillon

Identifiants firmware (5)

N° HardwareN° Software (chip)VersionLogiciel de mise à jourCalculateur
02612045591037359462 1.46.00440LRHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.01040GPHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00440GSHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00540LPHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00640GMHJ.a2l BOSCH ME7.0

Notes calculateur

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!
Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. To work on this ECU you can use NewTrasdata On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!