VOLVO TRUCK FL MK I 240 7.2L 184kW/247HP LUCAS

Calculateur LUCAS PLCC 28HC256 · 250 CV (184 kW) · 7200 cc · Diesel sovralimentato

Base de données calculateursVOLVO TRUCK › VOLVO TRUCK FL MK I 240 7.2L 184kW/247HP LUCAS

Retrouvez les identifiants du firmware (numéros hardware, software et mise à jour), les options de tuning disponibles et comment obtenir le fichier d'origine ou reprogrammé.

✓ Tuning par fichier (flash) 17 versions firmware

Données véhicule

MarqueVOLVO TRUCK
ModèleFL MK I
Moteur240 7.2L 184kW/247HP LUCAS
Puissance d'origine250 CV / 184 kW
Cylindrée7200 cc
CarburantDiesel sovralimentato
Type de véhiculeTir

Calculateur

FabricantLUCAS
ModèlePLCC 28HC256
Mémoire / EPROM28HC256 PLCC32 256Kbit - EEprom 32K x 8

Opérations / options de tuning disponibles:

  • Injection au rallenti
  • Injection charge partielle
  • Injection à pleine charge
  • Limiteur de couple
  • Limiteur fumèes au rallentì
  • Limiteur de fumées charge partielle
  • Limiteur de fumeus à pleine charge

Identifiants firmware (17)

N° HardwareN° Software (chip)VersionLogiciel de mise à jourCalculateur
03161963XXXX3580 1.55.003 LUCAS PLCC 28HC256
03161965XXXX3076 1.55.003 LUCAS PLCC 28HC256
03161965XXXX1949 1.55.111 LUCAS PLCC 28HC256
03161965XXXX8864 1.55.001 LUCAS PLCC 28HC256
03161965XXXX1949 1.55.110 LUCAS PLCC 28HC256
03161965XXXX1481 1.55.004 LUCAS PLCC 28HC256
08192397XXXX0172 1.55.004 LUCAS PLCC 28HC256
08192397XXXX1949 1.55.003 LUCAS PLCC 28HC256
08192397XXXX1946 1.55.005 LUCAS PLCC 28HC256
08192397XXXX3672 1.55.002 LUCAS PLCC 28HC256
20412507XXXX3580 1.55.005 LUCAS PLCC 28HC256
20412508XXXX1949 1.55.116 LUCAS PLCC 28HC256
20412508XXXX3675 1.55.004 LUCAS PLCC 28HC256
20412508XXXX3672 1.55.002 LUCAS PLCC 28HC256
20577133XXXX3076 1.55.003 LUCAS PLCC 28HC256
20577133XXXX1949 1.55.002 LUCAS PLCC 28HC256
20577133XXXX8864 1.55.004 LUCAS PLCC 28HC256

Notes calculateur

Original EPROM 28HC256 PLCC 32 pins To read this EPROM with the EMP20 programmer you need PD28 adapters. Attention !! The EMP21 instead needs the PD32 adapters. On this epron can be set a KEY. WARNING !! With the eprom programmer EMP21 at first select device, then choose "DEVICE OPTIONS" and then "DISABLE SDP AFTER PROGRAM" (confirm with "OK"). With EMP20 once the eprom has been programmed, select "B" for disable data protection and confirm with "Y". This Setting File can be used for serial system NewGenius.