BMW 2 SERIES F22/F23/F44/F45/F46 225i 2.0L L4 16V 170kW/228HP MEVD17.2.3 — ECU BOSCH MEVD17.2.3

Find the firmware identifiers (hardware, software and update numbers), available tuning options and how to get the original or remapped file.

✓ Tuning via file (flash) ✓ Add-on module available 9 firmware versions

Get the file for this vehicle

Buy the file (original or remapped)Register on mastertuningfile.com and order the file

Are you a workshop or tuner?

Vehicle data

Brand	BMW
Model	2 SERIES F22/F23/F44/F45/F46
Engine	225i 2.0L L4 16V 170kW/228HP MEVD17.2.3
Stock power	231 CV / 17 kW
Displacement	2000 cc
Fuel	Benzina sovralimentato
Vehicle type	Auto

ECU

Manufacturer	BOSCH
Model	MEVD17.2.3
Memory / EPROM	MICRO ST TRICORE - 32768 - 400000

Available tuning operations / options:

Spark advance correction for soundtuning - nomal mode
Spark advance correction for soundtuning - sport mode
Base timing
Minimum advance allowed protection - motore caldo
Lambda/AFR full load/WOT
Lambda/AFR mixture at part load
Optimal spark timing/MBT
Optimal spark timing/MBT - emergency
Boost pressure limiter - advance correction
Boost pressure limiter - advance correction 2
Boost pressure limiter for diagnostics
Boost pressure limiter for diagnostics 2
Maximum torque limitation at clutch
Correction for boost pressure
Driver torque limit for clutch protection
Compression ratio for turbocharger protection
Engine torque reducing factor depending on engine speed
Engine torque reducing factor depending on temperature
HFM/HLM threshold for diagnosis
High pressure fuel pump setpoint
High pressure fuel pump setpoint - cold condition
High pressure fuel pump setpoint - full load
High pressure fuel pump setpoint - limp home mode
Intake pressure protection
Intake valve lift
Intake valve lift - cold
Intake valve lift - cold 3
Intake valve lift - limit
Intake valve lift - warm
Intake valve lift - warm 2
Torque limiter 2
Advance limiter - emergency
Basic value Lambda sensor
Lambda target value
Torque limiter
Torque limiter - AT
Torque limiter in full load
Lambda enrichment - open loop
Lambda minimum value for components protection
Lambda fat-running limit for component protection
RPM Limiter
RPM limit for ECT sensor
RPM limit for EOT sensor
Knock detection factor
Speed limiter
Maximum absolute effective torque
Maximum indicated torque
Maximum indicated torque for monitoring
Maximum boost pressure load
Throttle air mass flow calculation
Maximum rail pressure at start-up
Optimal engine moment
Pressure ratio depending on IAT
Maximum pressure ratio limit depending on temperature
Maximum pressure ratio limit depending on ECT
Specific pressure injection after starting
Turbo pressure variation control factor
Driver torque request
Driver torque request for low speed
Maximum threshold for detecting engine knock
Start of injection
Maximum upper tolerance intake pressure protection
Lower pressure control threshold
Theoretical maximum engine power
Turbo pressure sensor - lower threshold
Upper engine rpm threshold for diagnostic control
Upper pressure control threshold
Wastegate duty-cycle

Firmware identifiers (9)

Hardware No.	Software No. (chip)	Version	Update software	ECU
0000208C023B02	00002B5C131401	1.98.007	00002D9513140C	BOSCH MEVD17.2.3
0000208C023B03	0000360A1D1401	1.98.008	00002D951D1805	BOSCH MEVD17.2.3
0000208C023B04	0000360A4F1E01	1.98.008	00002D954F1E04	BOSCH MEVD17.2.3
0000208C023B04	0000360A631E01	1.98.005	00002D95631E02	BOSCH MEVD17.2.3
0000208C023B04	0000360A453201	1.98.006	00005539453202	BOSCH MEVD17.2.3
0000208C024505	0000360A953201	1.94.006	00002D95953201	BOSCH MEVD17.2.3
00003DE7023B05	000048B33B5001	1.98.006	00004C793B5003	BOSCH MEVD17.2.3
00003DE7023B05	000048B33B5001	1.98.012	000054BF3B500B	BOSCH MEVD17.2.3
00003DE7024505	000048B3591E01	1.98.014	0000688A591E65	BOSCH MEVD17.2.3

Vehicle technical notes

OBD located to the left of the driver's side, in the bulkhead close to the bonnet release lever.

ECU notes

MICRO Infineon Tricore TC1793 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata