MERCEDES TRUCK VARIO W670 813 D 4.3L L4 95kW/127HP TEMIC

Steuergerät TEMIC TEMIC PLD · 129 CV (95 kW) · 4300 cc · Diesel sovralimentato

Steuergeräte-DatenbankMERCEDES TRUCK › MERCEDES TRUCK VARIO W670 813 D 4.3L L4 95kW/127HP TEMIC

Hier finden Sie die Firmware-Kennungen (Hardware-, Software- und Update-Nummern), verfügbare Tuning-Optionen und wie Sie die Original- oder optimierte Datei erhalten.

✓ Tuning per Datei (Flash) 13 Firmware-Versionen

Fahrzeugdaten

MarkeMERCEDES TRUCK
ModellVARIO W670
Motor813 D 4.3L L4 95kW/127HP TEMIC
Serienleistung129 CV / 95 kW
Hubraum4300 cc
KraftstoffDiesel sovralimentato
FahrzeugtypTir

Steuergerät

HerstellerTEMIC
ModellTEMIC PLD
Speicher / EPROM29F400 PSOP44 4Mbit - Flash 256K x 16

Verfügbare Tuning-Optionen:

  • Max. Schwellenwert Luftmassenstrom durch den Kompressor
  • Ladedruckbegrenzer
  • Motor Überhitzungsschutz Kennfeld
  • Motor Überhitzungsschutz Kennfeld 2
  • Motor Überhitzungsschutz Kennfeld 3
  • Basis Moment beim Anlassen des Motors
  • Motorleerlaufdrehzahl für ECT-Sensor
  • Einspritzwinkel
  • Einspritzwinkel 2
  • Einspritzwinkelkorrektur
  • PLD Förderwinkel
  • Rauchbegrenzer
  • Angegebener Maximaldrehmoment
  • Maximale Drehmoment Wert

Firmware-Kennungen (13)

Hardware-Nr.Software-Nr. (Chip)VersionUpdate-SoftwareSteuergerät
05A 1.54.005 TEMIC TEMIC PLD
B50 1.54.117 TEMIC TEMIC PLD
B50 1.54.116 TEMIC TEMIC PLD
07B 1.54.014 TEMIC TEMIC PLD
J51 1.54.016 TEMIC TEMIC PLD
E51 1.54.018 TEMIC TEMIC PLD
53G 1.54.012 TEMIC TEMIC PLD
09D 1.54.007 TEMIC TEMIC PLD
07B 1.54.006 TEMIC TEMIC PLD
56E 1.54.123 TEMIC TEMIC PLD
06A 1.54.022 TEMIC TEMIC PLD
J51 1.54.133 TEMIC TEMIC PLD
09D 1.54.015 TEMIC TEMIC PLD

Steuergerät-Hinweise

Original EPROM PSOP 44 pins 29F200BB. This Setting File can be used for serial system NewGenius. ATTENTION: before proceding with any serial operation please read carefully the corresponding protocol serial manual.
Original EPROM PSOP 44 pins 29F400BB. This Setting File can be used for serial system NewGenius. ATTENTION: before proceding with any serial operation please read carefully the corresponding protocol serial manual.
Original EPROM PSOP 44 pins 29F400BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. This setting file is enabled for the GENIUS serial tuning; it is required the specific TEMIC connection cable.Please read the specific handbook in order to open the ECU and to solder the wire inside it. On this epron can be set a KEY.
Original EPROM PSOP 44 pins 29F400BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. This setting file is enabled for the GENIUS serial tuning; it is required the specific TEMIC connection cable.Please read the specific handbook in order to open the ECU and to solder the wire inside it.