TOYOTA COROLLA (E140/E150) 1.8L L4 16V VVT-i 104kW/141HP DENSO

ECU DENSO 275036-1152 · 141 CV (104 kW) · 1800 cc · Benzina aspirato

ECU-databaseTOYOTA › TOYOTA COROLLA (E140/E150) 1.8L L4 16V VVT-i 104kW/141HP DENSO

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 11 firmwareversies

Voertuiggegevens

MerkTOYOTA
ModelCOROLLA (E140/E150)
Motor1.8L L4 16V VVT-i 104kW/141HP DENSO
Standaard vermogen141 CV / 104 kW
Cilinderinhoud1800 cc
BrandstofBenzina aspirato
VoertuigtypeAuto

ECU

FabrikantDENSO
Model275036-1152
Geheugen / EPROMMICRO NEC 76F0039AGD - 512Kbit - 80000

Beschikbare tuning-opties:

  • Spark advance correction for ECT sensor
  • Requested spark advance - high octane
  • Requested spark advance - low octane
  • Spark advance correction - valve timing position 1
  • Electronic throttle control
  • Lambda correction f(IAT)
  • Lambda correction f(ECT)
  • Lambda correction f(ECT) 2
  • Torque limiter 2
  • Advance limiter for component protection 1
  • Basic value setpoint Lambda sensor
  • Torque limiter
  • Lambda enrichment - open loop
  • Lambda driver wish
  • % relative air filling limit depending on IAT
  • Driver torque request
  • Driver torque request 2
  • Exhaust gas temperature sensor
  • Variable valve timing - inlet

Firmware-identificatoren (11)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
89663-02B90- 1.67.015302B9000 DENSO 275036-1152
89663-02C20- 1.67.006302C2000 DENSO 275036-1152
89663-02B70- 1.67.033302B7000 DENSO 275036-1152
89663-02B21- 1.67.021302B2100 DENSO 275036-1152
89663-02K30- 1.67.007302K3000 DENSO 275036-4820
89663-02L40-A 1.67.014302L4000 DENSO 275036-4820
89663-02S21- 1.67.011302S2100 DENSO 275036-4820
89663-02L30- 1.67.007302L3000 DENSO 275036-4820
89663-02S31- 1.67.018302S3100 DENSO 275036-4820
89663-02551- 1.67.00730255100 DENSO 275036-7341
89663-12C70-A 1.51.024312C7000 DENSO 275922-5280/5380

ECU-notities

Microprocessor NEC 76F0038AGD This Setting File can be used for serial system NewGenius. This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Microprocessor NEC 76F0040GD This Setting File can be used for serial system NewGenius. This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Microprocessor NEC 76F0085 This Setting File can be used for serial system NewGenius. This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata