VOLVO V70 Mk1 2.0L 16V TURBO 132kW/177HP ME7.0

ECU BOSCH ME7.0 · 179 CV (132 kW) · 2000 cc · Benzina sovralimentato

ECU-databaseVOLVO › VOLVO V70 Mk1 2.0L 16V TURBO 132kW/177HP ME7.0

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 10 firmwareversies

Voertuiggegevens

MerkVOLVO
ModelV70 Mk1
Motor2.0L 16V TURBO 132kW/177HP ME7.0
Standaard vermogen179 CV / 132 kW
Cilinderinhoud2000 cc
BrandstofBenzina sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelME7.0
Geheugen / EPROM29F800 PSOP44 8Mbit - Flash 512K x 16

Beschikbare tuning-opties:

  • Base timing
  • Optimal spark timing/MBT
  • Boost pressure limiter 3
  • Boost pressure limit control
  • Height correction for boost pressure
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Maximum pressure ratio limit for diagnosis
  • Exhaust gas temperature
  • Lambda enrichment for components protection
  • RPM Limiter
  • Boost pressure linearization
  • Lambda driver wish
  • Maximum boost pressure load
  • Throttle air mass flow calculation
  • Optimal engine moment
  • Power limit torque table
  • Driver torque request
  • Driver torque request 2
  • Throttle angle management
  • Variable intake pulsation correction

Firmware-identificatoren (10)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
02612045591037359462 1.46.01020KTHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00420FMFP.a2l BOSCH ME7.0
02612045591037359462 1.46.01120NGHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.02320FMFP.a2l BOSCH ME7.0
02612045591037359462 1.46.00720FWHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.01140GMHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00820FWHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00940GPHJ.a2l BOSCH ME7.0
02612045591037359462 1.46.00520FMFP.a2l BOSCH ME7.0
02612045591037359462 1.46.02420FLFP.a2l BOSCH ME7.0

ECU-notities

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! To work on this ECU you can use NewTrasdata
Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!