SEAT IBIZA (6J) 1.4L 16V TSI CUPRA 132kW/177HP MED17.5.5

ECU BOSCH MED17.5.5 · 179 CV (132 kW) · 1400 cc · Benzina sovralimentato

ECU-databaseSEAT › SEAT IBIZA (6J) 1.4L 16V TSI CUPRA 132kW/177HP MED17.5.5

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 11 firmwareversies

Voertuiggegevens

MerkSEAT
ModelIBIZA (6J)
Motor1.4L 16V TSI CUPRA 132kW/177HP MED17.5.5
Standaard vermogen179 CV / 132 kW
Cilinderinhoud1400 cc
BrandstofBenzina sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelMED17.5.5
Geheugen / EPROMMICRO ST TRICORE - 12032 Kbit - 178000

Beschikbare tuning-opties:

  • Base timing
  • Optimal spark timing/MBT
  • Advance correction
  • Height correction for boost pressure
  • Desired engine load calculation
  • Compression ratio for turbocharger protection
  • Compression ratio limiting for compressor depending on IAT sensor
  • Exhaust gas temperature
  • High pressure fuel pump setpoint
  • High fuel pressure pump limit for ECT sensor
  • High fuel pressure pump limit
  • High pressure fuel pump setpoint - limp home mode
  • High-pressure fuel pump - in catalyst heating monitoring mode
  • Lambda enrichment for components protection
  • Lambda correction for exhaust manifold temperature
  • RPM Limiter
  • RPM Limiter 2
  • RPM limiter 3
  • RPM limiter 4
  • RPM limiter - N
  • RPM limiter in Park position
  • RPM limit for EOT sensor
  • Knock detection factor
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Maximum intake manifold pressure
  • Max torque profile
  • Optimal engine moment
  • Relative permissible torque from the pedal position in torque limitation
  • Relative permissible torque from the pedal position in torque limitation - sport/race mode
  • Driver torque request
  • Driver torque request AWD
  • Driver torque request for reverse gear
  • Throttle angle management

Firmware-identificatoren (11)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
1.94.01903C906027AE 9251 BOSCH MED17.5.5
1.94.02303C906027AE 9251 BOSCH MED17.5.5
1.94.03603C906027AE 5034 BOSCH MED17.5.5
1.94.02603C906027AE 7931 BOSCH MED17.5.5
1.94.04603C906027AE 9971 BOSCH MED17.5.5
1.94.00903C906026G 6412 BOSCH MED17.5.5
1.94.01003C906027AE 9736 BOSCH MED17.5.5
1.94.02503C906027AE 6597 BOSCH MED17.5.5
1.94.01203C906026G 4537 BOSCH MED17.5.5
1.94.01803C906027AE 9970 BOSCH MED17.5.5
1.94.03603C906027AE 9972 BOSCH MED17.5.5

ECU-notities

This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata WARNING! ECU MED9 - IX/CL = injection at full load, decrease the values to enrich the injection
MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1767 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata

Aanvullende modules beschikbaar

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

→ See all add-on modules on the shop