NISSAN NAVARA/FRONTIER (D22) 2.5L TD 99kW/132HP ZEXEL

ECU BOSCH 23710 VC 102 · 133 CV (98 kW) · 2500 cc · Diesel sovralimentato

ECU-databaseNISSAN › NISSAN NAVARA/FRONTIER (D22) 2.5L TD 99kW/132HP ZEXEL

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 10 firmwareversies

Voertuiggegevens

MerkNISSAN
ModelNAVARA/FRONTIER (D22)
Motor2.5L TD 99kW/132HP ZEXEL
Standaard vermogen133 CV / 98 kW
Cilinderinhoud2500 cc
BrandstofDiesel sovralimentato
VoertuigtypeLCV

ECU

FabrikantBOSCH
Model23710 VC 102
Geheugen / EPROM27C020 DIL32/PLCC32 2Mbit - Eprom 256K x 8

Beschikbare tuning-opties:

  • Injection for boost pressure sensor 1
  • Boost pressure limiter
  • Boost pressure
  • Injection period
  • Torque limiter
  • Smoke limiter
  • Torque limiter 1-2 gear
  • Constant pressure control
  • Air mass flow

Firmware-identificatoren (10)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
407917-069 1.00.004 BOSCH 23710 VC 102
08207 1.00.019 BOSCH TDI 2PLCC
23710407917 1.00.007 BOSCH TDI 2PLCC
26126 1.00.005 BOSCH TDI 2PLCC
38522 1.00.012 BOSCH TDI 2PLCC
407917-0720478228 1020/1120 1.00.004 BOSCH TDI 2PLCC
407917-0723478228 1023/1123 1.00.016 BOSCH TDI 2PLCC
23710 VK560 1.00.009 ZEXEL ZEXEL
38528 1.00.005 ZEXEL ZEXEL
38726 1.00.008 ZEXEL ZEXEL

Technische voertuignotities

OBD located under the steering column, above the pedals. Visible or hidden by a plastic lid.

ECU-notities

2 original EPROM 27C010 or 29F010 PLCC 32 pins. To read this EPROM with the EMP20/21 programmer you need PD32 adapters. 16 Bit setting file. This works with a file obtained with the merge of EPROM HHH + LLL. On this epron can be set a KEY.
2 original EPROM 27C010 PLCC 32 pins. To read this EPROM with the EMP20 programmer you need PD28 adapters. Attention !! The EMP21 instead needs the PD32 adapters. On this epron can be set a KEY. 16 Bit setting file. This works with a file obtained with the merge of EPROM HHH + LLL.
2 original EPROM 27C010 or 29F010 PLCC 32 pins. To read this EPROM with the EMP20/21 programmer you need PD32 adapters. 16 Bit setting file. This works with a file obtained with the merge of EPROM HHH + LLL.

Aanvullende modules beschikbaar

→ See all add-on modules on the shop