Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 11 firmwareversies
Voertuiggegevens
| Merk | NEW HOLLAND AGRICULTURE |
| Model | T |
| Motor | 7030 6.7L 132kW/177HP EDC16C39 |
| Standaard vermogen | 179 CV / 132 kW |
| Cilinderinhoud | 6700 cc |
| Brandstof | Diesel sovralimentato |
| Voertuigtype | Tractor |
ECU
| Fabrikant | BOSCH |
| Model | EDC16C39 |
| Geheugen / EPROM | M58BW016DB PQFP80 - Flash 3_V 512 x 32 |
Beschikbare tuning-opties:
- Boost pressure limiter
- Boost pressure
- Boost pressure in aftertreatment modes
- Correction for boost pressure
- Desired fuel quantity map for open loop
- EGR valve control
- Exhaust gas temperature
- Exhaust gas temperature 2
- Protection for engine overheating
- Max CAT temperature threshold for component protection
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Gearbox maximum torque allowed
- Gearbox maximum torque allowed 2
- Injection period
- Injection opening time related to inj. pressure
- Injection mass at high temperature
- Injection mass at low temperature
- Maximum fuel quantity for turbine overspeed prevention
- Injection limit - turbocharger protection
- Max injection limit
- L
- Torque limiter 3
- Torque limiter 4
- Torque limiter
- Torque limiter during particulate filter overloading - pressure
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Minimum LSU sensor temperature limit - heater control
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature limit - heater control
- Maximum LSU sensor temperature for O2
- LSU temperature threshold PID heater governor activation
- MAP - limp home mode
- Maximum indicated torque
- Protection for air load overheating
- Injection quantity for engine overheating protection
- Injection quantity for engine overheating protection 2
- Injection quantity for engine overheating protection 3
- Protection for fuel overheating
- Protection for fuel overheating 2
- Protection for oil overheating
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter 3
- Specific injection pressure limiter for diagnostics
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure in aftertreatment modes
- Air mass flow
- Driver torque request
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Torque limiter in recovery mode 2
- Torque limiter in recovery mode 3
- Torque model - torque to fuel quantity conversion
- Torque model for performance limiter
- Volumetric efficiency
- Voluimetric efficiency
- Volumetric efficiency - correction
- Volumetric efficiency - EGR correction
- Turbocharger volumetric efficiency
Firmware-identificatoren (11)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | — |
1.67.008 | P400V41 itoldn10.cme |
BOSCH EDC16C39 |
| — | — |
1.67.012 | P400V41 itoldn10.cmb |
BOSCH EDC16C39 |
| — | — |
1.67.086 | P400V41 itoldn08.cme |
BOSCH EDC16C39 |
| — | — |
1.67.023 | P400V41 itoldn08.cme |
BOSCH EDC16C39 |
| — | — |
1.67.007 | P400V41 itoldn0a.cmb |
BOSCH EDC16C39 |
| — | — |
1.67.007 | P400V41 itocdn07.cme |
BOSCH EDC16C39 |
| — | — |
1.67.008 | P400V41 itoldn08.cme |
BOSCH EDC16C39 |
| — | — |
1.67.008 | P400V41 itoldn0a.cmb |
BOSCH EDC16C39 |
| — | — |
1.67.007 | P400V41 itoldn0b.cmb |
BOSCH EDC16C39 |
| — | — |
1.67.007 | P400V41 itoldn0b.cme |
BOSCH EDC16C39 |
| — | — |
1.67.008 | P400V41 itoldn0a.cme |
BOSCH EDC16C39 |
ECU-notities
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocesor Motorola MPC561/2/3/4. To work on this ECU you can use NewTrasdata This Setting File can be used for serial programming system NewGenius.
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
