MV AGUSTA TURISMO VELOCE 800 17->19 92kW

ECU ELDOR NEMO 2.0 · 125 CV (92 kW) · 800 cc · Benzina aspirato

ECU-databaseMV AGUSTA › MV AGUSTA TURISMO VELOCE 800 17->19 92kW

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 15 firmwareversies

Voertuiggegevens

MerkMV AGUSTA
ModelTURISMO VELOCE 800
Motor17->19 92kW
Standaard vermogen125 CV / 92 kW
Cilinderinhoud800 cc
BrandstofBenzina aspirato
VoertuigtypeMoto

ECU

FabrikantELDOR
ModelNEMO 2.0
Geheugen / EPROMMicro BGA ST SPC563M64 - 12288 Kbit - 180000

Beschikbare tuning-opties:

  • Advance correction cylinder 2
  • Base timing
  • Lambda/AFR mixture at part load
  • Optimal spark timing/MBT
  • Spark advance correction for ECT sensor
  • Desired engine load calculation
  • Lambda correction
  • Lambda Correction 2
  • RPM Limiter
  • RPM Limiter 2
  • Lambda driver wish
  • Speed limiter
  • Air mass flow
  • Driver torque request
  • Driver torque request - MT
  • Requested torque map set 2
  • Requested torque map set 3
  • Throttle angle management

Firmware-identificatoren (15)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
M3M36R-0911 1.00.0030911M010 ELDOR NEMO 2.0
M3M36R-0911 1.00.0030911MC10 ELDOR NEMO 2.0
M3M36R-0911 1.00.0030911MM07 ELDOR NEMO 2.0
M3M36R-0911 1.00.0030911MP07 ELDOR NEMO 2.0
M3M36R-0911 1.00.0030911MR07 ELDOR NEMO 2.0
M3M36R-0911 1.00.0030911MU10 ELDOR NEMO 2.0
M3M36R-0912 1.00.0030912M011 ELDOR NEMO 2.0
M3M36R-0912 1.00.0030912MC11 ELDOR NEMO 2.0
M3M36R-0912 1.00.0030912MU11 ELDOR NEMO 2.0
M3M36R-0909 1.00.0050909M009 ELDOR NEMO 2.0
M3M36R-0909 1.00.0030909MC09 ELDOR NEMO 2.0
M3M36R-0909 1.00.0030909MM06 ELDOR NEMO 2.0
M3M36R-0909 1.00.0030909MP06 ELDOR NEMO 2.0
M3M36R-0909 1.00.0030909MR06 ELDOR NEMO 2.0
M3M36R-0909 1.00.0030909MU09 ELDOR NEMO 2.0

Technische voertuignotities

OBD placed under the saddle

ECU-notities

Microprocessor SPC563M64 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation.