MERCURY MARINE MARINE ENGINE 3.0L TDI 73kW/99HP EDC16CP34

ECU BOSCH EDC16U31/U34/CP34 · 100 CV (74 kW) · 3000 cc · Diesel sovralimentato

ECU-databaseMERCURY MARINE › MERCURY MARINE MARINE ENGINE 3.0L TDI 73kW/99HP EDC16CP34

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 5 firmwareversies

Voertuiggegevens

MerkMERCURY MARINE
ModelMARINE ENGINE
Motor3.0L TDI 73kW/99HP EDC16CP34
Standaard vermogen100 CV / 74 kW
Cilinderinhoud3000 cc
BrandstofDiesel sovralimentato
VoertuigtypeMarine

ECU

FabrikantBOSCH
ModelEDC16U31/U34/CP34
Geheugen / EPROMAm29BDD160G PQFP80 - Flash 3_V 512 x 32

Beschikbare tuning-opties:

  • Main injection duration angle
  • Main injection duration angle 2
  • Main injection duration angle 3
  • Main injection duration angle 4
  • Boost pressure limiter
  • Maximum engine boost pressure F (atmospheric pressure)
  • Boost pressure
  • Boost pressure in aftertreatment modes
  • EGR valve control
  • EGR valve control 2
  • EGR valve control in aftertreatment modes
  • EGR valve control in aftertreatment modes 2
  • EGR valve control in aftertreatment modes 3
  • Exhaust gas temperature
  • Protection for engine overheating
  • Basic torque management at engine cranking
  • Engine idle vs. ECT sensor
  • Engine idle vs. ECT sensor 2
  • Engine idle vs. ECT sensor 3
  • Engine idle vs. ECT sensor 4
  • Gearbox maximum torque allowed
  • Maximum injection period
  • Injection opening time related to inj. pressure
  • Injection 1
  • Injection in aftertreatment modes 1
  • L
  • Torque limiter
  • Smoke limiter
  • RPM limiter - fuel cut
  • Lambda value of the smoke limitation
  • Lambda value of the smoke limitation in aftertreatment modes
  • Minimum LSU sensor temperature for O2
  • Maximum LSU sensor temperature for O2
  • LSU temperature threshold PID heater governor activation
  • Protection for air load overheating
  • Protection for exhaust gas temperature before turbine
  • Protection for fuel overheating
  • Protection for oil overheating
  • Air mass flow
  • CAT downstream temperature sensor characterization
  • Torque limiter for the 1st gear selected
  • Torque limiter for the 2nd gear selected
  • Torque limiter for the 3rd gear selected
  • Torque limiter for the 4th gear selected
  • Torque limiter for the 5th gear selected
  • Torque limiter for the 6th gear selected
  • Torque limiter for selected gear
  • Torque limiter for for reverse gear
  • Torque limiter for the APS/BPS
  • Torque limiter in recovery mode
  • Torque limiter in recovery mode 2
  • Torque limiter in recovery mode 3
  • Volumetric efficiency
  • Turbocharger volumetric efficiency
  • Variable geometry duty cycle limit
  • Variable geometry duty cycle limit 2

Firmware-identificatoren (5)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
1037387094 1.67.02406V910401D 0010 BOSCH EDC16U31/U34/CP34
1037380760 1.67.01706V910401 0010 BOSCH EDC16U31/U34/CP34
1037387094 1.67.02206V910401E 0010 BOSCH EDC16U31/U34/CP34
0123456789 1.67.01606V910401D 0010 BOSCH EDC16U31/U34/CP34
0123456789 1.67.01206V910401D V006 BOSCH EDC16U31/U34/CP34

ECU-notities

Original EPROM Am29BDD160G PQFP 80 Pin - Microprocessor Motorola MPC56x. This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata