Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 18 firmwareversies
Voertuiggegevens
| Merk | JEEP |
| Model | COMPASS (MK49) |
| Motor | 2.0L 16V CRD 103kW/138HP EDC16+ |
| Standaard vermogen | 140 CV / 103 kW |
| Cilinderinhoud | 2000 cc |
| Brandstof | Diesel sovralimentato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | EDC16U31 |
| Geheugen / EPROM | M58BW016DB PQFP80 - Flash 3_V 512 x 32 |
Beschikbare tuning-opties:
- Smoke limiter 2
- Main injection duration angle
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure 2
- Boost pressure in aftertreatment modes
- Boost pressure in aftertreatment modes 2
- EGR valve control
- EGR valve control 2
- EGR valve control 3
- EGR valve control in aftertreatment modes
- EGR valve control in aftertreatment modes 2
- Exhaust gas temperature
- Exhaust gas temperature 2
- Protection for engine overheating
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Gearbox maximum torque allowed
- Injection period
- Injection period - correction
- Maximum injection period
- Max injection limit - limp mode
- Injection 1
- Injection in aftertreatment modes 1
- L
- Torque limiter
- Smoke limiter
- RPM limiter - fuel cut
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation in aftertreatment modes
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature for O2
- LSU temperature threshold PID heater governor activation
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Air mass flow
- Driver torque request
- CAT downstream temperature sensor characterization
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for selected gear
- Torque limiter for for reverse gear
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Torque limiter in recovery mode 2
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
Firmware-identificatoren (18)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | 1037389270 |
1.67.014 | 1037389270 |
BOSCH EDC16U31 |
| — | 1037383828 |
1.67.009 | 1037396079 |
BOSCH EDC16U31 |
| — | 1037396086 |
1.67.009 | 1037396086 |
BOSCH EDC16U31 |
| — | 1037386358 |
1.67.013 | 1037396079 |
BOSCH EDC16U31 |
| — | 1037391837 |
1.67.011 | 1037396076 |
BOSCH EDC16U31 |
| — | 1037386358 |
1.67.010 | 1037389270 |
BOSCH EDC16U31 |
| — | 1037394140 |
1.67.011 | 1037394140 |
BOSCH EDC16U31 |
| — | 1037389270 |
1.67.017 | 1037396079 |
BOSCH EDC16U31 |
| — | 1037383828 |
1.67.009 | 1037389270 |
BOSCH EDC16U31 |
| — | 1037396085 |
1.67.006 | 1037396085 |
BOSCH EDC16U31 |
| — | 1037390628 |
1.67.009 | 1037390629 |
BOSCH EDC16U31 |
| — | 1037390629 |
1.67.020 | 1037390629 |
BOSCH EDC16U31 |
| — | 1037390629 |
1.67.013 | 1037396082 |
BOSCH EDC16U31 |
| — | 1037383828 |
1.67.024 | 1037383828 |
BOSCH EDC16U31 |
| — | 1037390628 |
1.67.009 | 1037396085 |
BOSCH EDC16U31 |
| — | 1037386358 |
1.67.012 | 1037389271 |
BOSCH EDC16U31 |
| — | 1037390629 |
1.67.015 | 1037396085 |
BOSCH EDC16U31 |
| — | 1037390630 |
1.67.006 | 1037390629 |
BOSCH EDC16U31 |
ECU-notities
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocesor Motorola MPC561/2/3/4. This Setting File can be used for serial system : Genius or NewGenius. To work on this ECU you can use NewTrasdata
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4. This Setting File can be used for serial system : Genius or NewGenius. To work on this ECU you can use NewTrasdata
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4. This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
