FIAT TALENTO 1.6L 16V EcoJet 107KW/143HP EDC17C84

ECU BOSCH EDC17C84 · 145 CV (107 kW) · 1600 cc · Diesel sovralimentato

ECU-databaseFIAT › FIAT TALENTO 1.6L 16V EcoJet 107KW/143HP EDC17C84

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 11 firmwareversies

Voertuiggegevens

MerkFIAT
ModelTALENTO
Motor1.6L 16V EcoJet 107KW/143HP EDC17C84
Standaard vermogen145 CV / 107 kW
Cilinderinhoud1600 cc
BrandstofDiesel sovralimentato
VoertuigtypeLCV

ECU

FabrikantBOSCH
ModelEDC17C84
Geheugen / EPROMMICRO ST TRICORE - 20480 Kbit - 280000

Beschikbare tuning-opties:

  • Boost pressure limiter
  • Boost pressure limiter 2
  • Boost pressure
  • Boost pressure in aftertreatment modes
  • Maximum torque limitation at clutch
  • Effective engine torque setpoint for safety
  • Max accepted exhaust gas temperature value after turbine
  • Exhaust gas temperature value before turbine in regeneration mode
  • Exhaust gas temperature value before turbine in regular injection mode
  • Max accepted exhaust gas temperature value at particulate sensor
  • Max torque correction factor for IAT sensor
  • Max torque correction factor for IAT sensor 2
  • Max torque correction factor for IAT sensor in aftertreatment modes
  • Max torque correction factor for IAT sensor in aftertreatment modes 2
  • Basic torque management at engine cranking
  • Basic torque management at engine cranking 2
  • Basic torque management at engine cranking 3
  • Engine idle vs. ECT sensor
  • Gearbox maximum torque allowed
  • Injection period
  • Injection opening time related to inj. pressure
  • Injection period in aftertreatment modes 3
  • Torque limiter
  • Torque limiter for diagnostic
  • Maximum absolute effective torque in ECO mode
  • Maximum indicated torque
  • Maximum indicated torque in regeneration mode
  • Maximum indicated torque - safety condition
  • Maximum indicated torque - safety condition 2
  • Max exhaust gas temperature value before turbine in regeneration mode
  • Max exhaust gas temperature value before turbine in regular injection mode
  • Turbine temperature maximum value
  • Specific injection pressure limiter
  • Specific injection pressure limiter 4
  • Specific injection pressure limiter in aftertreatment modes
  • Specific injection pressure limiter for diagnostics
  • Maximum pressure ratio limit depending on temperature
  • Specific injection pressure
  • Specific injection pressure in aftertreatment modes
  • Specific injection pressure in aftertreatment modes 2
  • Driver torque request
  • Driver torque request Sport mode
  • Maximum temperature before turbine for diagnosis
  • Temperature before turbine setpoint during npu, spu and injection mode
  • Torque limiter for EFT sensor
  • Torque limiter in recovery mode
  • Torque limiter in recovery mode 2
  • Torque limiter in recovery mode 3
  • Torque model - fuel quantity to torque conversion
  • Torque model - fuel quantity to torque conversion 2
  • Torque model - fuel quantity to torque conversion in aftertreatment modes
  • Torque model - torque to fuel quantity conversion

Firmware-identificatoren (11)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
10SW008509 1.94.00410SW011006 BOSCH EDC17C84
10SW008509 1.94.01010SW011017 BOSCH EDC17C84
10SW008509 1.94.01310SW011008 BOSCH EDC17C84
10SW014336 1.94.00810SW039575 BOSCH EDC17C84
10SW082584 1.94.00410SW082584 BOSCH EDC17C84
10SW099468 1.94.01010SW099468 BOSCH EDC17C84
10SW049391 1.94.01110SW049391 BOSCH EDC17C84
10SW014336 1.94.01210SW032700 BOSCH EDC17C84
10SW014336 1.94.01810SW032702 BOSCH EDC17C84
10SW014336 1.94.00910SW027337 BOSCH EDC17C84
10SW014336 1.94.01410SW027337 BOSCH EDC17C84

ECU-notities

Microprocessor TC1782 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata

Aanvullende modules beschikbaar

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):