DUCATI MULTISTRADA 950 18->21 83kW

ECU BOSCH ME17.9.21 · 113 CV (83 kW) · 950 cc · Benzina aspirato

ECU-databaseDUCATI › DUCATI MULTISTRADA 950 18->21 83kW

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 19 firmwareversies

Voertuiggegevens

MerkDUCATI
ModelMULTISTRADA 950
Motor18->21 83kW
Standaard vermogen113 CV / 83 kW
Cilinderinhoud950 cc
BrandstofBenzina aspirato
VoertuigtypeMoto

ECU

FabrikantBOSCH
ModelME17.9.21
Geheugen / EPROMMICRO ST TRICORE - 12288 Kbit - 180000

Beschikbare tuning-opties:

  • Base timing
  • Minimum advance allowed
  • Minimum advance allowed protection
  • Optimal spark timing/MBT
  • Advance at part load
  • Knock correction advance max
  • Desired engine load calculation
  • Desired engine load calculation 2
  • Lambda correction f(IAT)
  • Desired throttle angle
  • Exhaust gas temperature
  • Exhaust gas temperature threshold for component protection
  • Engine torque limit for transmission protection
  • Factor to correct fuel delivery system
  • Engine idle vs. ECT sensor
  • Engine idle vs. ECT sensor 2
  • Rpm threshold fuel cut
  • Lambda enrichment for components protection
  • Lambda minimum value for components protection
  • Lambda correction for exhaust manifold temperature
  • RPM Limiter
  • RPM limiter - N
  • RPM limiter - R
  • Speed limiter
  • Throttle air mass flow calculation
  • Maximum throttle angle opening for a given RPM
  • Nominal throttle opening
  • Optimal engine moment
  • Power limit torque table
  • Requested torque map set 1
  • Requested torque map set 1 - monitoring
  • Requested torque map set 1 - monitoring 2
  • Requested torque map set 2
  • Requested torque map set 2 - monitoring
  • Requested torque map set 2 - monitoring 2
  • Requested torque map set 3
  • Requested torque map set 3 - monitoring
  • Requested torque map set 3 - monitoring 2
  • Driver torque request - MT
  • Requested torque map set 4 - monitoring
  • Requested torque map set 4 - monitoring 2

Firmware-identificatoren (19)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
1.91.01910SW049460 BOSCH ME17.9.21
1.91.00910SW093539 BOSCH ME17.9.21
1.91.00310SW018073 BOSCH ME17.9.21
1.91.00810SW093535 BOSCH ME17.9.21
1.91.01410SW094549 BOSCH ME17.9.21
1.91.01310SW025676 BOSCH ME17.9.21
1.91.00910SW069812 BOSCH ME17.9.21
1.91.02410SW018073 BOSCH ME17.9.21
1.91.01110SW097828 BOSCH ME17.9.21
1.91.03510SW093540 BOSCH ME17.9.21
1.91.00710SW068312 BOSCH ME17.9.21
1.91.00610SW049461 BOSCH ME17.9.21
1.91.01310SW018074 BOSCH ME17.9.21
1.91.01910SW018073 BOSCH ME17.9.21
1.91.01110SW087741 BOSCH ME17.9.21
1.91.01010SW073472 BOSCH ME17.9.21
1.91.00610SW056591 BOSCH ME17.9.21
1.91.01010SW088892 BOSCH ME17.9.21
1.91.01410SW058157 BOSCH ME17.9.21

ECU-notities

Microprocessor TC1724 To work on this ECU you can use NewTrasdata This Setting File can be used for serial system NewGenius.
Microprocessor TC1724 To work on this ECU you can use NewTrasdata This Setting File can be used for serial system NewGenius. ATTENTION - 35kW reduced power version file.
Microprocessor TC1724 To work on this ECU you can use NewTrasdata This Setting File can be used for serial system NewGenius. ATTENTION - 70kW reduced power version file.