DS DS3 1.4L 16V HDI 50kW/67HP EDC16C34

ECU BOSCH EDC16C34 · 68 CV (5 kW) · 1400 cc · Diesel sovralimentato

ECU-databaseDS › DS DS3 1.4L 16V HDI 50kW/67HP EDC16C34

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 1 firmwareversies

Voertuiggegevens

MerkDS
ModelDS3
Motor1.4L 16V HDI 50kW/67HP EDC16C34
Standaard vermogen68 CV / 5 kW
Cilinderinhoud1400 cc
BrandstofDiesel sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelEDC16C34
Geheugen / EPROMAm29BDD160G PQFP80 - Flash 3_V 512 x 32

Beschikbare tuning-opties:

  • Maximum engine boost pressure F (atmospheric pressure)
  • Boost pressure in aftertreatment modes
  • Boost pressure F (temperature)
  • EGR valve control
  • Basic torque management at engine cranking
  • Injection period
  • Injection opening time related to inj. pressure
  • Injection period in aftertreatment modes
  • Injection period in aftertreatment modes 2
  • Injection period in aftertreatment modes 3
  • Max injection limit
  • Max injection limit - limp mode
  • J
  • Injection in aftertreatment modes 1
  • Injection in aftertreatment modes 2
  • Injection in aftertreatment modes 3
  • Torque limiter 2
  • Torque limiter
  • Lambda value of the smoke limitation
  • Injection quantity for engine overheating protection
  • Injection quantity for engine overheating protection 3
  • Protection for fuel overheating
  • Specific injection pressure limiter
  • Specific injection pressure limiter for EFT sensor
  • Specific injection pressure
  • Specific injection pressure in aftertreatment modes
  • Specific pressure injection after starting
  • Air mass flow
  • Driver torque request
  • Driver torque request for high speed - AT
  • Driver torque request for low speed - AT
  • Driver torque request for reverse gear
  • CAT downstream temperature sensor characterization
  • Torque limiter for the 1st gear selected
  • Torque limiter for the 2nd gear selected
  • Torque limiter for the 3rd gear selected
  • Torque limiter for the 4th gear selected
  • Torque limiter for the 5th gear selected
  • Torque limiter for the 6th gear selected
  • Torque limiter for selected gear - AT
  • Torque limiter for for reverse gear
  • Torque limiter for the APS/BPS
  • Torque limiter in recovery mode
  • Take-off torque law in Normal mode
  • Variable geometry duty cycle limit in regeneration mode
  • Variable geometry duty cycle limit in regeneration mode 2

Firmware-identificatoren (1)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
1.67.0191037501009 BOSCH EDC16C34

ECU-notities

EPROM AM29BDD160G / S29CD016G PQFQ 80 Pin - Microprocessor MPC 563/4 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata

Aanvullende modules beschikbaar

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

→ See all add-on modules on the shop