Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 11 firmwareversies
Voertuiggegevens
| Merk | AUDI |
| Model | Q5 (8R) |
| Motor | 2.0L 16V TDI 120kW/161HP EDC17CP14 |
| Standaard vermogen | 163 CV / 12 kW |
| Cilinderinhoud | 2000 cc |
| Brandstof | Diesel sovralimentato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | EDC17CP14 |
| Geheugen / EPROM | MICRO ST TRICORE - 16384 Kbit - 200000 |
Beschikbare tuning-opties:
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Maximum torque limitation at clutch
- Regeneration limit for DPF
- EGR valve control
- EGR valve control 2
- EGR valve control 3
- Protection for engine overheating
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Injection period
- Injection period 2
- Injection period 3
- Injection opening time related to inj. pressure
- Initialization values over pressure control valve
- J
- L
- Smoke limiter
- Lambda reference
- Lambda value of the smoke limitation
- Minimum LSU sensor temperature limit - heater control
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature limit - heater control
- Maximum LSU sensor temperature for O2
- LSU temperature threshold PID heater governor activation
- Speed limiter
- Maximum indicated torque
- Maximum indicated torque for monitoring
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter for EFT sensor
- Relative permissible torque from the pedal position in torque limitation
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure in aftertreatment modes
- Specific pressure injection after starting
- Driver torque request
- Driver torque request AWD
- Driver torque request for reverse gear
- CAT downstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- DPF upstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Torque limiter for selected gear
- Torque limiter for for reverse gear
- Setpoint maximum turbocharger speed
- Torque limiter for the APS/BPS
- Torque model - torque to fuel quantity conversion - particulate regeneration mode
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
- Variable geometry duty cycle limit 3
- Variable geometry duty cycle limit 4
- Variable geometry duty cycle limit 5
- Variable geometry duty cycle limit in regeneration mode
Firmware-identificatoren (11)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | — |
1.00.013 | 03L906022NJ 4389 |
BOSCH EDC17CP14 |
| — | — |
1.94.005 | 03L906022HN 8482 |
BOSCH EDC17CP14 |
| — | — |
1.00.013 | 03L906019AR 8475 |
BOSCH EDC17CP14 |
| — | — |
1.00.013 | 03L906019AR 6574 |
BOSCH EDC17CP14 |
| — | — |
1.94.006 | 03L906019AR 9978 |
BOSCH EDC17CP14 |
| — | — |
1.00.007 | 03L997019D 0450 |
BOSCH EDC17CP14 |
| — | — |
1.00.015 | 03L906019AR 6309 |
BOSCH EDC17CP14 |
| — | — |
1.00.018 | 03L906019NJ 5510 |
BOSCH EDC17CP14 |
| — | — |
1.94.006 | 03L906022NJ 9978 |
BOSCH EDC17CP14 |
| — | — |
1.94.011 | 03L906019AR 9977 |
BOSCH EDC17CP14 |
| — | — |
1.00.007 | 03L906022HN 2481 |
BOSCH EDC17CP14 |
Technische voertuignotities
OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.
ECU-notities
MICRO Infineon Tricore TC1796 It is possible to support this ECU via OBDII using NewGenius and protocol FLASH_0506 WITHOUT PERFORMING the unlock patch and starting always from a 16Mbit TOTAL size file. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1796 To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1796 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
