AUDI A7 (4G8) 3.0L V6 24V TDI 150kW/201HP EDC17CP44 — ECU BOSCH EDC17CP44

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 4 firmwareversies

Verkrijg het bestand voor dit voertuig

Koop het bestand (origineel of geremapt)Registreer op mastertuningfile.com en bestel het bestand

Ben je een garage of tuner?

Voertuiggegevens

Merk	AUDI
Model	A7 (4G8)
Motor	3.0L V6 24V TDI 150kW/201HP EDC17CP44
Standaard vermogen	204 CV / 15 kW
Cilinderinhoud	3000 cc
Brandstof	Diesel sovralimentato
Voertuigtype	Auto

ECU

Fabrikant	BOSCH
Model	EDC17CP44
Geheugen / EPROM	MICRO ST TRICORE - 32768 Kbit - 400000

Beschikbare tuning-opties:

Boost pressure limiter
Boost pressure limiter 2
Boost pressure
Protection for cylinder head overheating
Regeneration limit for DPF
Regeneration limit for DPF 2
EGR valve control
EGR valve control 2
EGR valve control 3
EGR valve control 4
Max accepted exhaust gas temperature value before turbine
Max accepted exhaust gas temperature value before turbine 2
Protection for engine overheating
Protection for engine overheating 2
Protection for engine overheating 3
Engine reference power at crankshaft
Basic torque management at engine cranking
Engine idle vs. ECT sensor
Injection period
Injection period 2
Injection period 3
Injection period 4
Injection period 5
Injection opening time related to inj. pressure
Initialization values over pressure control valve
Injection 1
J
Torque limiter
Torque limiter for diagnostic
Torque limiter for diagnostic 4
Torque limiter during inactive pre-injection
Smoke limiter
RPM limit for ECT sensor
RPM limit for ECT sensor 2
Lambda reference
Lambda value of the smoke limitation
Minimum LSU sensor temperature limit - heater control
Minimum LSU sensor temperature for O2
Maximum LSU sensor temperature limit - heater control
Maximum LSU sensor temperature for O2
LSU temperature setpoint
LSU temperature threshold PID heater governor activation
Speed limiter
Speed limiter - reverse gear
Maximum indicated torque
Maximum indicated torque for monitoring
Maximum engine torque at crank shaft
Protection for air load overheating
Protection for exhaust gas temperature before turbine
Protection for exhaust gas temperature before turbine 2
Protection for fuel overheating
Protection for oil overheating
Pressure control map over pressure regulating valve
Specific injection pressure limiter
Specific injection pressure limiter 2
Specific injection pressure limiter 3
Specific injection pressure limiter 4
Relative permissible torque from the pedal position in torque limitation
Specific injection pressure
Specific injection pressure 2
Specific injection pressure 3
Specific injection pressure - cold correction
Driver torque request
Driver torque request 2
Driver torque request 3
Driver torque request - AT
Driver torque request for reverse gear
CAT downstream temperature sensor characterization
CAT upstream temperature sensor characterization
DPF downstream temperature sensor characterization
Turbo upstream temperature sensor characterization
Torque limiter for the 1st gear selected
Torque limiter for the 2nd gear selected
Torque limiter for the 3rd gear selected
Torque limiter for the 4th gear selected
Torque limiter for the 5th gear selected
Torque limiter for the 6th gear selected
Torque limiter for the 7th gear selected
Torque limiter for the 8th gear selected
Torque limiter for the 9th gear selected
Torque limiter for for reverse gear
Torque limiter for the APS/BPS
Variable geometry duty cycle limit
Variable geometry duty cycle limit 2

Firmware-identificatoren (4)

Hardware-nr.	Software-nr. (chip)	Versie	Update-software	ECU
—	—	1.94.014	4G0907311G 0002	BOSCH EDC17CP44
—	—	1.00.029	4G0907311E 0002	BOSCH EDC17CP44
—	—	1.94.009	4G0907311G 0001	BOSCH EDC17CP44
—	—	1.00.015	8K5907311 0001	BOSCH EDC17CP44

Technische voertuignotities

OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.

ECU-notities

MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata