AUDI A4 (B9/8W) 50 3.0L 24V TDI 210kW/281HP MD1CP004 — ECU BOSCH MD1CP004

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 5 firmwareversies

Verkrijg het bestand voor dit voertuig

Koop het bestand (origineel of geremapt)Registreer op mastertuningfile.com en bestel het bestand

Ben je een garage of tuner?

Voertuiggegevens

Merk	AUDI
Model	A4 (B9/8W)
Motor	50 3.0L 24V TDI 210kW/281HP MD1CP004
Standaard vermogen	286 CV / 21 kW
Cilinderinhoud	3000 cc
Brandstof	Diesel sovralimentato
Voertuigtype	Auto

ECU

Fabrikant	BOSCH
Model	MD1CP004
Geheugen / EPROM	Micro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte

Beschikbare tuning-opties:

Boost pressure limiter
Maximum engine boost pressure F (atmospheric pressure)
Boost pressure
Boost pressure 2
Boost pressure 3
Boost pressure 4
Boost pressure 5
Boost pressure 6
Boost pressure 7
Boost pressure 8
Protection for cylinder head overheating
Maximum torque limitation at clutch
Max accepted exhaust gas temperature value before turbine
Max accepted exhaust gas temperature value before turbine 2
Max accepted exhaust gas temperature value before turbine 3
Protection for engine overheating
Basic torque management at engine cranking
Injection period
Injection period 10
Injection period 11
Injection period 13
Injection period 14
Injection period 15
Injection period 16
Injection period 17
Injection period 18
Injection period 19
Injection period 4
Injection period 5
Injection period 6
Injection period 7
Injection period 8
Injection period 9
Injection period limit
Injection period limit 2
Injection opening time related to inj. pressure
Injection 1
Injection 2
Injection 3
J
Injection 5
Torque limiter 2
L
Torque limiter 5
Torque limiter
LCL
Lambda value of the smoke limitation
Lambda value of the smoke limitation 2
Lambda value of the smoke limitation 3
Speed limiter
Speed limiter 2
Max torque profile - AT
Protection for air load overheating
Protection for exhaust gas temperature before turbine
Protection for exhaust gas temperature before turbine 2
Protection for fuel overheating
Protection for oil overheating
Pressure control map over pressure regulating valve
Specific injection pressure limiter
Specific injection pressure
Specific injection pressure 2
Specific injection pressure 3
Specific injection pressure 4
Specific injection pressure 5
Driver torque request
Driver torque request 2
CAT downstream temperature sensor characterization
CAT upstream temperature sensor characterization
DPF downstream temperature sensor characterization
Turbo upstream temperature sensor characterization
Start of injection
Start of injection 2
Torque limiter for the APS/BPS
Torque limiter in recovery mode
Turbocharger volumetric efficiency
Variable geometry duty cycle limit

Firmware-identificatoren (5)

Hardware-nr.	Software-nr. (chip)	Versie	Update-software	ECU
—	—	1.02.012	8W0907401G 0004	BOSCH MD1CP004
—	—	1.02.017	8W0907401B 0003	BOSCH MD1CP004
—	—	1.02.008	8W0907401K 0002	BOSCH MD1CP004
—	—	1.02.014	8W0907401L 0001	BOSCH MD1CP004
—	—	1.02.011	8W0907401H 0003	BOSCH MD1CP004

ECU-notities

Microprocessor BGA FREESCALE SPC57xxx This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata

Micro Infineon Tricore TC298TP This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata