Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 4 firmwareversies
Voertuiggegevens
| Merk | AUDI |
| Model | A4 (B8/8K) |
| Motor | 3.0L V6 24V TDI 200kW/268HP MD1CP004 |
| Standaard vermogen | 272 CV / 2 kW |
| Cilinderinhoud | 3000 cc |
| Brandstof | Diesel sovralimentato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | MD1CP004 |
| Geheugen / EPROM | Micro BGA FREESCALE - 8192 Kbit - 800000 |
Beschikbare tuning-opties:
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure 2
- Boost pressure 3
- Boost pressure 4
- Boost pressure 5
- Boost pressure 6
- Boost pressure 7
- Protection for cylinder head overheating
- Max accepted exhaust gas temperature value before turbine
- Protection for engine overheating
- Basic torque management at engine cranking
- Injection period
- Injection period 10
- Injection period 12
- Injection period 13
- Injection period 14
- Injection period 15
- Injection period 16
- Injection period 17
- Injection period 18
- Injection period 3
- Injection period 4
- Injection period 5
- Injection period 6
- Injection period 7
- Injection period 8
- Injection period 9
- Injection period limit
- Injection period limit 2
- Injection opening time related to inj. pressure
- Injection opening time related to inj. pressure 2
- Injection 1
- Injection 2
- Injection 3
- J
- Injection 5
- Injection 6
- Torque limiter 2
- Torque limiter
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Lambda value of the smoke limitation 3
- Speed limiter
- Speed limiter 2
- Max torque profile - AT
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure 4
- Driver torque request
- Driver torque request 2
- Driver torque request 3
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Start of injection
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
Firmware-identificatoren (4)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | — |
1.02.021 | 8W0907401E 0001 |
BOSCH MD1CP004 |
| — | — |
1.02.025 | 8W0907401E 0003 |
BOSCH MD1CP004 |
| — | — |
1.02.014 | 8W0907401E 0004 |
BOSCH MD1CP004 |
| — | — |
1.02.023 | 8W0997401 0001 |
BOSCH MD1CP004 |
ECU-notities
Microprocessor BGA FREESCALE SPC57xxx This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
