Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 27 firmwareversies
Voertuiggegevens
| Merk | AUDI |
| Model | A4 (B8/8K) |
| Motor | 2.0L 16V TFSI 155kW/208HP MED17.1 |
| Standaard vermogen | 211 CV / 155 kW |
| Cilinderinhoud | 2000 cc |
| Brandstof | Benzina sovralimentato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | MED17.1 |
| Geheugen / EPROM | MICRO ST TRICORE - 16384 Kbit - 200000 |
Beschikbare tuning-opties:
- Engine ignition timing versus temperature
- Base timing
- Advance at idle speed
- Optimal spark timing/MBT
- Height correction for boost pressure
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Maximum pressure ratio limit for diagnosis
- Exhaust gas temperature
- Factor to correct fuel delivery system
- Filling factor limit
- Filling factor limit 2
- Factor for reducing maximum filling
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- RPM Limiter
- RPM Limiter 2
- RPM limiter 3
- RPM limiter 4
- Engine speed limitation at high motor temperature
- Engine speed limit temperature based
- Lambda driver wish
- Knock detection factor
- Speed limiter
- Maximum boost pressure load
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Optimal engine moment
- Power limit torque table
- Relative permissible torque from the pedal position in torque limitation
- Relative permissible torque from the pedal position in torque limitation 2
- Pressure ratio depending on IAT
- Maximum pressure ratio limit depending on temperature
- Driver torque request
- Throttle angle management
Firmware-identificatoren (27)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | — |
1.94.010 | 8K2907115AG 0003 |
BOSCH MED17.1 |
| — | — |
1.94.051 | 8K2907115P 0002 |
BOSCH MED17.1 |
| — | — |
1.94.004 | 4G0907115P 0005 |
BOSCH MED17.1 |
| — | — |
1.94.030 | 8K2907115AL 0001 |
BOSCH MED17.1 |
| — | — |
1.94.027 | 8K2907115P 0006 |
BOSCH MED17.1 |
| — | — |
1.94.021 | 8K2907115AE 0002 |
BOSCH MED17.1 |
| — | — |
1.94.011 | 8K5907115H 0003 |
BOSCH MED17.1 |
| — | — |
1.94.010 | 8K5907115C 0006 |
BOSCH MED17.1 |
| — | — |
1.94.010 | 8K2907115J 0005 |
BOSCH MED17.1 |
| — | — |
1.94.014 | 8K2907115Q 0006 |
BOSCH MED17.1 |
| — | — |
1.94.016 | — |
BOSCH MED17.1 |
| — | — |
1.94.016 | 8K5907115C 0005 |
BOSCH MED17.1 |
| — | — |
1.94.017 | 8K5907115F 0008 |
BOSCH MED17.1 |
| — | — |
1.94.020 | 8K2907115AJ 0002 |
BOSCH MED17.1 |
| — | — |
1.94.079 | 8K5907115 0006 |
BOSCH MED17.1 |
| — | — |
1.94.011 | 8K2907115AD 0003 |
BOSCH MED17.1 |
| — | — |
1.94.043 | 8K2907115AE 0001 |
BOSCH MED17.1 |
| — | — |
1.94.005 | 8K5907115C 0007 |
BOSCH MED17.1 |
| — | — |
1.94.006 | 8K2907115AA 0007 |
BOSCH MED17.1 |
| — | — |
1.94.016 | 8K2907115AG 0002 |
BOSCH MED17.1 |
| — | — |
1.94.027 | 8K2907115P 0008 |
BOSCH MED17.1 |
| — | — |
1.94.018 | 8K5907115 0008 |
BOSCH MED17.1 |
| — | — |
1.94.010 | 8K2907115AG 0004 |
BOSCH MED17.1 |
| — | — |
1.94.022 | 8K2907115AA 0005 |
BOSCH MED17.1 |
| — | — |
1.94.016 | 8K2907115P 0005 |
BOSCH MED17.1 |
| — | — |
1.94.014 | 8K5907115J 0002 |
BOSCH MED17.1 |
| — | — |
1.94.010 | 8K5907115C 0003 |
BOSCH MED17.1 |
Technische voertuignotities
OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.
ECU-notities
MICRO Infineon Tricore TC1766 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1796 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1796 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. WARNING: this ECU can be modified ONLY with the BOOT system NewTrasdata or NewGenius flash_0313.
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
