Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
11 firmwareversies
Voertuiggegevens
| Merk | AUDI |
| Model | A3 (8V) |
| Motor | 1.6L 16V TDI 81kW/109HP EDC17C64 |
| Standaard vermogen | 110 CV / 81 kW |
| Cilinderinhoud | 1600 cc |
| Brandstof | Diesel sovralimentato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | EDC17C64 |
| Geheugen / EPROM | MICRO ST TRICORE - 32768 Kbit - 400000 |
Beschikbare tuning-opties:
- Boost pressure limiter
- Boost pressure limiter 2
- Boost pressure limiter 3
- Boost limiter correction for APS/BPS sensor
- Protection for cylinder head overheating
- Engine load - ceiling
- Maximum torque limitation at clutch
- Max accepted exhaust gas temperature value before turbine
- Max accepted exhaust gas temperature value before turbine 2
- Max accepted exhaust gas temperature value at particulate sensor
- Protection for engine overheating
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Engine idle vs. ECT sensor 2
- Engine idle vs. ECT sensor 3
- Engine idle vs. ECT sensor 4
- Engine idle vs. ECT sensor 5
- Injection period
- Injection period 2
- Injection period 3
- Injection period 4
- Injection period - correction
- Maximum injection period
- Injection opening time related to inj. pressure
- Injection 1
- J
- Injection 3
- Injection 4
- Injection 5
- Injection 6
- Boost pressure deviation limits for overboost detection
- Boost pressure deviation limits for overboost detection 2
- Boost pressure deviation limit for underboost detection
- Boost pressure deviation limit for underboost detection 2
- Torque limiter
- Smoke limiter
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Lambda value of the smoke limitation 3
- Lambda value of the smoke limitation 5
- Speed limiter
- Maximum indicated torque
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for exhaust gas temperature before turbine 3
- Protection for fuel overheating
- Protection for oil overheating
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter 3
- Specific injection pressure limiter 4
- Specific injection pressure limiter for EFT sensor
- Specific injection pressure limiter for EOT sensor
- Relative permissible torque from the pedal position in torque limitation
- Maximum pressure ratio limit depending on temperature
- Specific injection pressure
- Specific air mass charge
- Specific air mass charge 2
- Specific air mass charge 3
- Specific air mass charge 4
- Specific air mass charge 5
- Specific air mass charge 6
- QC
- Driver torque request
- Driver torque request AWD
- Driver torque request for reverse gear
- Torque limiter for selected gear
- Setpoint maximum turbocharger speed
- Overboost timing
- Overboost timing 2
- Overboost timing 3
- Overboost timing 4
- Turbocharger volumetric efficiency
Firmware-identificatoren (11)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | — |
1.94.024 | 04L906021AP 9228 |
BOSCH EDC17C64 |
| — | — |
1.94.024 | 04L906021FD 8122 |
BOSCH EDC17C64 |
| — | — |
1.94.002 | 04L906021AP 5569 |
BOSCH EDC17C64 |
| — | — |
1.94.011 | 04L906021FD 9231 |
BOSCH EDC17C64 |
| — | — |
1.94.020 | 04L906021AQ 8210 |
BOSCH EDC17C64 |
| — | — |
1.94.011 | 04L906021FD 7856 |
BOSCH EDC17C64 |
| — | — |
1.94.030 | 04L906021AQ 9229 |
BOSCH EDC17C64 |
| — | — |
1.94.023 | 04L906021AN 8209 |
BOSCH EDC17C64 |
| — | — |
1.94.016 | 04L906021AQ 6824 |
BOSCH EDC17C64 |
| — | — |
1.94.010 | 04L906021AP 6561 |
BOSCH EDC17C64 |
| — | — |
1.94.018 | 04L906021AP 8212 |
BOSCH EDC17C64 |
Technische voertuignotities
OBD located under the steering column, above the pedals. Visible or hidden by a plastic lid.
ECU-notities
MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
