Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 24 firmwareversies
Voertuiggegevens
| Merk | AUDI |
| Model | A3 (8P) MY08 |
| Motor | 1.8L 16V TFSI 118kW/158HP MED17.5 |
| Standaard vermogen | 160 CV / 118 kW |
| Cilinderinhoud | 1800 cc |
| Brandstof | Benzina sovralimentato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | MED17.5 |
| Geheugen / EPROM | MICRO ST TRICORE - 12032 Kbit - 178000 |
Beschikbare tuning-opties:
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Optimal spark timing/MBT
- Advance correction
- Height correction for boost pressure
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Maximum pressure ratio limit for diagnosis
- Exhaust gas temperature
- Filling factor limit
- Filling factor limit 2
- Factor for reducing maximum filling
- Gearbox maximum torque allowed
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- High fuel pressure pump limit
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- Torque limiter at high EGT
- RPM Limiter
- RPM limiter 3
- RPM limiter 4
- RPM Limiter 5
- RPM limiter - N
- RPM limiter in Park position
- RPM limit for ECT sensor
- Lambda driver wish
- Knock detection factor
- Speed limiter
- Speed limiter 2
- Maximum boost pressure load
- Maximum boost pressure load 2
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Optimal engine moment
- Power limit torque table
- Relative permissible torque from the pedal position in torque limitation
- Relative permissible torque from the pedal position in torque limitation - sport/race mode
- Pressure ratio depending on IAT
- Maximum pressure ratio limit depending on temperature
- Driver torque request
- Driver torque request AWD
- Driver torque request for reverse gear
- Exhaust gas temperature sensor
- Throttle angle management
Firmware-identificatoren (24)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| — | — |
1.94.025 | 8P7907115D 0020 |
BOSCH MED17.5 |
| — | — |
1.94.009 | 8P7907115M 0020 |
BOSCH MED17.5 |
| — | — |
1.94.017 | 8P7907115 0010 |
BOSCH MED17.5 |
| — | — |
1.94.008 | 8P7907115F 0020 |
BOSCH MED17.5 |
| — | — |
1.94.029 | 8P7907115L 0020 |
BOSCH MED17.5 |
| — | — |
1.94.003 | 8P1907115B 0060 |
BOSCH MED17.5 |
| — | — |
1.94.009 | 8P1907115B 0080 |
BOSCH MED17.5 |
| — | — |
1.94.025 | 8P7907115F 0010 |
BOSCH MED17.5 |
| — | — |
1.94.004 | 8P7907115G 0040 |
BOSCH MED17.5 |
| — | — |
1.94.022 | 8P7907115L 0030 |
BOSCH MED17.5 |
| — | — |
1.94.009 | 8P7907115E 0020 |
BOSCH MED17.5 |
| — | — |
1.94.047 | 8P7907115 0020 |
BOSCH MED17.5 |
| — | — |
1.94.018 | 8P7907115G 0030 |
BOSCH MED17.5 |
| — | — |
1.94.008 | 8P7907115L 0040 |
BOSCH MED17.5 |
| — | — |
1.94.023 | 8P7907115K 0040 |
BOSCH MED17.5 |
| — | — |
1.94.009 | 8P7907115F 0050 |
BOSCH MED17.5 |
| — | — |
1.94.002 | 8P7907115A 0010 |
BOSCH MED17.5 |
| — | — |
1.94.013 | 8P7907115K 0030 |
BOSCH MED17.5 |
| — | — |
1.94.012 | 8P1907115B 0070 |
BOSCH MED17.5 |
| — | — |
1.94.033 | 8P7907115H 0030 |
BOSCH MED17.5 |
| — | — |
1.94.006 | 8P7907115D 0050 |
BOSCH MED17.5 |
| — | — |
1.94.015 | 8P7907115G 0050 |
BOSCH MED17.5 |
| — | — |
1.94.028 | 8P7907115K 0020 |
BOSCH MED17.5 |
| — | — |
1.94.026 | 8P7907115G 0020 |
BOSCH MED17.5 |
Technische voertuignotities
OBD located under the steering column, above the pedals. Visible or hidden by a plastic lid.
ECU-notities
MICRO Infineon Tricore TC1766 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
