Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.
✓ Tuning via bestand (flash)
✓ Aanvullende module beschikbaar 7 firmwareversies
Voertuiggegevens
| Merk | ALFA ROMEO |
| Model | BRERA |
| Motor | 3.2L V6 24V JTS 191kW/256HP MED7.6.2 |
| Standaard vermogen | 260 CV / 191 kW |
| Cilinderinhoud | 3200 cc |
| Brandstof | Benzina aspirato |
| Voertuigtype | Auto |
ECU
| Fabrikant | BOSCH |
| Model | MED7.6.2 |
| Geheugen / EPROM | 29F800 PSOP44 8Mbit - Flash 512K x 16 |
Beschikbare tuning-opties:
- Base timing
- Optimal spark timing/MBT
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Exhaust gas temperature
- High pressure fuel pump setpoint
- High pressure fuel pump setpoint 2
- Torque limiter for diagnostic
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- RPM Limiter
- Lambda driver wish
- Knock detection factor
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Optimal engine moment
- Offset tolerance depending on permissible torque
- Relative permissible torque from the pedal position in torque limitation
- Driver torque request
- Throttle angle management
- Variable intake pulsation correction
Firmware-identificatoren (7)
| Hardware-nr. | Software-nr. (chip) | Versie | Update-software | ECU |
|---|
| 0261S01043 | 1037379553 |
1.93.015 | — |
BOSCH MED7.6.2 |
| 0261S01043 | 1037386439 |
1.93.012 | — |
BOSCH MED7.6.2 |
| 0261S01044 | 1037383282 |
1.93.004 | — |
BOSCH MED7.6.2 |
| 0261S01044 | 1037500859 |
1.93.006 | — |
BOSCH MED7.6.2 |
| 0261S01062 | 1037392825 |
1.93.006 | — |
BOSCH MED7.6.2 |
| 0261S01063 | 1037393962 |
1.93.008 | — |
BOSCH MED7.6.2 |
| 0261S01064 | 1037393963 |
1.93.001 | — |
BOSCH MED7.6.2 |
Technische voertuignotities
OBD located to the left of the driver's side, under the steering column and behind the bulkhead or the lid in the fuse box area.
ECU-notities
Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! Attention! If you use the serial system: before start the program, disconnect the feeding on the fans radiator. This Setting File can be used for serial system : Genius or NewGenius.
Verkrijg het bestand voor dit voertuig
Tools om deze ECU te lezen en schrijven
