VOLKSWAGEN TIGUAN Mk1 2.0L 16V TFSI 147kW/197HP MED17.5

ECU BOSCH MED17.5 · 200 CV (147 kW) · 2000 cc · Benzina sovralimentato

ECU 数据库VOLKSWAGEN › VOLKSWAGEN TIGUAN Mk1 2.0L 16V TFSI 147kW/197HP MED17.5

查找固件标识(硬件、软件和升级编号)、可用的调校选项,以及如何获取原始或改写文件。

✓ 通过文件调校 (flash) 39 固件版本

车辆数据

品牌VOLKSWAGEN
型号TIGUAN Mk1
发动机2.0L 16V TFSI 147kW/197HP MED17.5
原厂功率200 CV / 147 kW
排量2000 cc
燃料Benzina sovralimentato
车辆类型Auto

ECU

制造商BOSCH
型号MED17.5
存储 / EPROMMICRO ST TRICORE - 12032 Kbit - 178000

可用的调校选项:

  • Maximum air charge for overboost protection with turbocharger fault
  • Base timing
  • Optimal spark timing/MBT
  • Advance correction
  • Height correction for boost pressure
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Maximum pressure ratio limit for diagnosis
  • Exhaust gas temperature
  • Filling factor limit
  • Filling factor limit 2
  • Factor for reducing maximum filling
  • Gearbox maximum torque allowed
  • High pressure fuel pump setpoint
  • High fuel pressure pump limit for ECT sensor
  • High fuel pressure pump limit
  • Lambda enrichment for components protection
  • Lambda correction for exhaust manifold temperature
  • Torque limiter at high EGT
  • RPM Limiter
  • Lambda driver wish
  • Knock detection factor
  • Speed limiter
  • Maximum boost pressure load
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Optimal engine moment
  • Power limit torque table
  • Relative permissible torque from the pedal position in torque limitation
  • Relative permissible torque from the pedal position in torque limitation - sport/race mode
  • Pressure ratio depending on IAT
  • Maximum pressure ratio limit depending on temperature
  • Driver torque request
  • Driver torque request AWD
  • Driver torque request for reverse gear
  • Exhaust gas temperature sensor
  • Throttle angle management

固件标识 (39)

硬件号软件号 (chip)版本升级软件ECU
1.94.02106J906026G 3321 BOSCH MED17.5
1.94.00206J997026L 0608 BOSCH MED17.5
1.94.00506J997026M 0609 BOSCH MED17.5
1.94.01506J906026T 3170 BOSCH MED17.5
1.94.01406J906026S 3169 BOSCH MED17.5
1.94.00206J906026G 8217 BOSCH MED17.5
1.94.01906J906026GB 2454 BOSCH MED17.5
1.94.01406J906026CT 4300 BOSCH MED17.5
1.94.00806J906026H 4298 BOSCH MED17.5
1.94.02206J906026EJ 5839 BOSCH MED17.5
1.94.00806J906026CJ 3185 BOSCH MED17.5
1.94.00706J997026J 0398 BOSCH MED17.5
1.94.01706J906026T 4302 BOSCH MED17.5
1.94.00906J906026CT 5346 BOSCH MED17.5
1.94.01806J906026EH 7448 BOSCH MED17.5
1.94.01106J906026T 9776 BOSCH MED17.5
1.94.01606J906026DN 5893 BOSCH MED17.5
1.94.00406J906026FP 7681 BOSCH MED17.5
1.94.00306J906026EH 8502 BOSCH MED17.5
1.94.00306J906026F 4296 BOSCH MED17.5
1.94.02906J906026CT 6996 BOSCH MED17.5
1.94.00306J906026FM 7679 BOSCH MED17.5
1.94.01106J906026CG 3183 BOSCH MED17.5
1.94.02106J906026FH 7327 BOSCH MED17.5
1.94.01306J906026S 4301 BOSCH MED17.5
1.94.01006J906026T 2723 BOSCH MED17.5
1.94.00606J997029P 1519 BOSCH MED17.5.2
1.94.02106J906027GD 5373 BOSCH MED17.5.2
1.94.02706J997027R 0401 BOSCH MED17.5.2
1.94.00806J906027GC 5372 BOSCH MED17.5.2
1.94.01906J906027EC 4093 BOSCH MED17.5.2
1.94.00506J906027GD 3409 BOSCH MED17.5.2
1.94.02706J906027Q 6975 BOSCH MED17.5.2
1.94.01206J906027HS 7827 BOSCH MED17.5.2
1.94.00406J997029N 1518 BOSCH MED17.5.2
1.94.01706J906027EC 4953 BOSCH MED17.5.2
1.94.01506J906027FB 8221 BOSCH MED17.5.2
1.94.01506J906027KB 3231 BOSCH MED17.5.2
1.94.02006J906027JP 1335 BOSCH MED17.5.2

ECU 说明

MICRO Infineon Tricore TC1766 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1767 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata