SEGWAY SNARLER AT6 21->25 32kW

ECU BOSCH MSE6.0 · 44 CV (32 kW) · 570 cc · Benzina aspirato

ECU-databaseSEGWAY › SEGWAY SNARLER AT6 21->25 32kW

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 14 firmwareversies

Voertuiggegevens

MerkSEGWAY
ModelSNARLER AT6
Motor21->25 32kW
Standaard vermogen44 CV / 32 kW
Cilinderinhoud570 cc
BrandstofBenzina aspirato
VoertuigtypeMoto

ECU

FabrikantBOSCH
ModelMSE6.0
Geheugen / EPROMMicro BGA ST SPC563M64 - 12288 Kbit - 180000

Beschikbare tuning-opties:

  • Base timing
  • Lambda/AFR full load/WOT
  • Lambda/AFR mixture at part load
  • Lambda/AFR mixture for engine temperature at crancking
  • Spark advance correction for ECT sensor
  • Desired engine load calculation
  • Exhaust gas temperature
  • Factor to correct fuel delivery system
  • Weighting map cold-start
  • Weighting map cold-start 2
  • Engine idle vs. ECT sensor
  • Engine idle vs. EOT sensor
  • Injection correction for ECT sensor
  • Injection correction for ECT sensor 2
  • Lambda enrichment for components protection
  • RPM Limiter
  • Speed limiter
  • MAP - limp home mode
  • Throttle air mass flow calculation
  • Throttle angle limitation
  • Throttle angle management
  • Volumetric efficiency

Firmware-identificatoren (14)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
XE0104B6A6 1.88.006F01RB0DN2K BOSCH MSE6.0
XE0104B8C6 1.88.005F01RB0D2C3 BOSCH MSE6.0
XE0104B861 1.88.008F01RB0DN2J BOSCH MSE6.0
XE0104B655 1.88.013F01RB0DN2J BOSCH MSE6.0
XE0104B8C2 1.88.008F01RB0D2C3 BOSCH MSE6.0
XE0104BBE2 1.88.005F01RB0D3ED BOSCH MSE6.0
XE0104B8BC 1.88.008F01RB0DM9Z BOSCH MSE6.0
XE0104BBE2 1.88.015F01RB0D3ED BOSCH MSE6.0
XE0104B857 1.88.016F01RB0DN2J BOSCH MSE6.0
XE0104B653 1.88.006F01RB0DN2J BOSCH MSE6.0
XE0104B8E4 1.88.008F01RB0D2C2 BOSCH MSE6.0
XE0104B8E6 1.88.006F01RB0D2C2 BOSCH MSE6.0
XE0104B6A6 1.88.008F01RB0DN2K BOSCH MSE6.0
XE0104B857 1.88.009F01RB0DN2J BOSCH MSE6.0

ECU-notities

Microprocessor SPC563M64 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata