English English Español Español Italiano Italiano Nederlands Nederlands Deutsch Deutsch 中文 中文 Français Français Lietuvių Lietuvių

SEAT LEON (1M) 1.8L 20V TURBO 110kW/150HP ME7.5

ECU BOSCH ME7.5 · 150 CV (11 kW) · 1800 cc · Benzina sovralimentato

ECU-database › SEAT › SEAT LEON (1M) 1.8L 20V TURBO 110kW/150HP ME7.5

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 9 firmwareversies

Verkrijg het bestand voor dit voertuig

Koop het bestand (origineel of geremapt)Registreer op mastertuningfile.com en bestel het bestand

Ben je een garage of tuner?

Voertuiggegevens

MerkSEAT
ModelLEON (1M)
Motor1.8L 20V TURBO 110kW/150HP ME7.5
Standaard vermogen150 CV / 11 kW
Cilinderinhoud1800 cc
BrandstofBenzina sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelME7.5
Geheugen / EPROM29F400 PSOP44 4Mbit - Flash 256K x 16

Beschikbare tuning-opties:

  • Base timing
  • Optimal spark timing/MBT
  • Boost pressure limiter
  • Boost pressure limiter 2
  • Boost pressure limiter 3
  • Boost pressure limit control
  • Height correction for boost pressure
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Exhaust gas temperature
  • Lambda enrichment for components protection
  • RPM Limiter 2
  • Boost pressure linearization
  • Lambda driver wish
  • Knock detection factor
  • Speed limiter
  • Maximum boost pressure load
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Optimal engine moment
  • Offset tolerance depending on permissible torque
  • Relative permissible torque from the pedal position in torque limitation
  • Maximum pressure ratio limit depending on temperature
  • Driver torque request
  • Driver torque request Sport mode
  • Throttle angle management
  • Variable intake pulsation correction

Firmware-identificatoren (9)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
02612065451037352761 1.21.02406A906032T 0003 BOSCH ME7.5
02612065511037352772 1.21.01806A906032BE 0001 BOSCH ME7.5
02612068661037360165 1.21.03106A906032DE 0001 BOSCH ME7.5
02612068861037360295 1.21.01006A906032DE 0002 BOSCH ME7.5
02612074401037360646 1.21.03306A906032HN 0001 BOSCH ME7.5
02612074401037363908 1.42.02706A906032HN 0002 BOSCH ME7.5
02612074461037362280 1.21.01406A906032HS 0002 BOSCH ME7.5
02612081151037366379 1.42.03006A906032MJ 0003 BOSCH ME7.5
02612085311037369040 1.42.02806A906032SJ 0010 BOSCH ME7.5

ECU-notities

Original EPROM PSOP 44 pins 29F400BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This Setting File can be used for serial system NewGenius. Attention! If you use the serial system: before start the program, disconnect the feeding on the fans radiator.
Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This Setting File can be used for serial system NewGenius. Attention! If you use the serial system: before start the program, disconnect the feeding on the fans radiator.
Attention! If you use the serial system: before start the program, disconnect the feeding on the fans radiator. Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This Setting File can be used for serial system NewGenius.

Verkrijg het bestand voor dit voertuig

Koop het bestand (origineel of geremapt)Registreer op mastertuningfile.com en bestel het bestand Ben je een garage of tuner?Bied deze diensten zelf aan: activeer je TuningFile-platform

Tools om deze ECU te lezen en schrijven

Flex Programmatore per rimappatura centraline e cambi automatici Flex Programmatore per rimappatura centraline e cambi automatici ECU + auto gearbox € 1.090 Kopen The Genius The Genius OBD + Bench € 2.500 Kopen

Andere SEAT

CORDOBA
1.6L 8V 56kW/75HP MOTRONIC CORDOBA
1.8L 8V 66kW/88HP MOTRONIC IBIZA (6K)
1.4L 8V 44kW/59HP MOTRONIC IBIZA (6K)
1.6L 8V 55kW/74HP MOTRONIC IBIZA (6K)
1.3L 8V 40kW/54HP MOTRONIC IBIZA (6K)
1.8L 8V 66kW/88HP MOTRONIC IBIZA (6K)
2.0L 8V 85kW/114HP SIEMENS TOLEDO (1M)
1.6L 8V 54kW/73HP MOTRONIC TOLEDO (1M)
2.0L 8V 85kW/114HP DIGIFANT 1.7 TOLEDO (1M)
2.0L 16V 110kW/147HP 5WP 4201

→ Alle ECU's SEAT