CASE IH MAXXUM EP MC 125 6.7L 101kW/135HP EDC7UC31

ECU BOSCH EDC7UC31 · 140 CV (103 kW) · 6700 cc · Diesel sovralimentato

ECU-databaseCASE IH › CASE IH MAXXUM EP MC 125 6.7L 101kW/135HP EDC7UC31

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) ✓ Aanvullende module beschikbaar 6 firmwareversies

Voertuiggegevens

MerkCASE IH
ModelMAXXUM EP
MotorMC 125 6.7L 101kW/135HP EDC7UC31
Standaard vermogen140 CV / 103 kW
Cilinderinhoud6700 cc
BrandstofDiesel sovralimentato
VoertuigtypeTractor

ECU

FabrikantBOSCH
ModelEDC7UC31
Geheugen / EPROMM58BW016DB PQFP80 - Flash 3_V 512 x 32

Beschikbare tuning-opties:

  • Boost pressure limiter
  • Boost pressure limiter 2
  • Boost pressure
  • Boost pressure 2
  • Boost pressure F (temperature)
  • Desired fuel quantity map for open loop
  • EGR valve control
  • Exhaust gas temperature
  • Max CAT temperature threshold for component protection
  • Basic torque management at engine cranking
  • Gearbox maximum torque allowed
  • Injection period
  • Injection opening time related to inj. pressure
  • Injection mass at high temperature
  • Injection mass at low temperature
  • Maximum fuel quantity for turbine overspeed prevention
  • Injection limit - turbocharger protection
  • Max injection limit
  • Max injection limit 2
  • Fuel quantity limitation after cold start
  • Max injection limit - limp mode
  • L
  • Torque limiter
  • Torque limiter during particulate filter overloading - pressure
  • Lambda value of the smoke limitation
  • MAP - limp home mode
  • Maximum indicated torque
  • Max torque profile
  • Injection quantity for engine overheating protection
  • Injection quantity for engine overheating protection 2
  • Protection for fuel overheating
  • Specific injection pressure limiter
  • Specific injection pressure limiter for diagnostics
  • Specific injection pressure
  • Specific injection pressure 2
  • Specific injection pressure in aftertreatment modes
  • Driver torque request
  • Torque limiter for selected gear
  • Torque limiter in recovery mode
  • Torque model - torque to fuel quantity conversion
  • Torque model for performance limiter
  • Torque model with performance limiter stage 1 is active
  • Torque model with performance limiter stage 2 active
  • Torque model with performance limiter after coldstart 1 active
  • Torque model with performance limiter stage 3 active
  • Turbocharger volumetric efficiency

Firmware-identificatoren (6)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
1.67.013P340VF01 ito1yg08_cp1 BOSCH EDC7UC31
1.67.008P340VF01 ito1yg08_cp1 BOSCH EDC7UC31
1.67.010P340VF01 ito1yg05_cp1 BOSCH EDC7UC31
1.67.011P340VF01 ito1yg05_cp1 BOSCH EDC7UC31
1.67.007P340VF01 ito1yg06_cp1 BOSCH EDC7UC31
1.67.006P340VF3 ito1yk02_cp1 BOSCH EDC7UC31

ECU-notities

To work on this ECU you can use NewTrasdata This Setting File can be used for serial programming system NewGenius.

Aanvullende modules beschikbaar

→ See all add-on modules on the shop