BMW 1 SERIES F20/F21/F52 125i 2.0L L4 16V 160kW/215HP MEVD17.2.9

ECU BOSCH MEVD17.2.9 · 218 CV (16 kW) · 2000 cc · Benzina sovralimentato

ECU-databaseBMW › BMW 1 SERIES F20/F21/F52 125i 2.0L L4 16V 160kW/215HP MEVD17.2.9

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 29 firmwareversies

Voertuiggegevens

MerkBMW
Model1 SERIES F20/F21/F52
Motor125i 2.0L L4 16V 160kW/215HP MEVD17.2.9
Standaard vermogen218 CV / 16 kW
Cilinderinhoud2000 cc
BrandstofBenzina sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelMEVD17.2.9
Geheugen / EPROMMICRO ST TRICORE - 32768 Kbit - 400000

Beschikbare tuning-opties:

  • Base timing
  • Base timing 2
  • Optimal spark timing/MBT
  • Boost pressure
  • Boost pressure 2
  • Desired engine load calculation
  • Maximum torque limitation at clutch
  • Characteristic line correction factor for pressure ratio for turbocharger overspeed protection
  • Gearbox maximum torque allowed
  • HFM/HLM threshold for diagnosis
  • High pressure fuel pump setpoint
  • Intake valve lift
  • Intake valve lift - full load
  • Torque limiter 2
  • L
  • Torque limiter for diagnostic
  • Lambda enrichment for components protection
  • RPM Limiter
  • RPM Limiter 2
  • RPM limit for ECT sensor
  • Boost pressure linearization
  • Knock detection factor
  • Speed limiter
  • Speed limiter 3
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Optimal engine moment
  • Pressure ratio depending on IAT
  • Maximum pressure ratio limit depending on temperature
  • Maximum pressure ratio limit depending on ECT
  • Requested engine filling
  • Driver torque request
  • Wastegate duty-cycle

Firmware-identificatoren (29)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
0000190101130100001C9F134601 1.98.01100001CE3134604 BOSCH MEVD17.2.9
0000190101270100001C9F1D3201 1.98.01000001CE31D3204 BOSCH MEVD17.2.9
0000190101270100001C9F1D4B01 1.94.00300001CE31D4B02 BOSCH MEVD17.2.9
0000190101270100001C9F1D4B01 1.94.00400001CE31D4C03 BOSCH MEVD17.2.9
0000190101270100001C9F1D4D01 1.98.00300001CE31D4D01 BOSCH MEVD17.2.9
0000190101270100001C9F1D4D01 1.98.0030000201C1D4D01 BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00400001F5C1D6E0E BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00300001CE31D6E0E BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00600001DA51D6E0C BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00500001CE31D6E0C BOSCH MEVD17.2.9
0000190101310100001C9F1D8201 1.94.00400001CE31D8203 BOSCH MEVD17.2.9
0000190101310100001C9F1D6402 1.98.00400001DA51D6402 BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.94.00400001CE31D6E09 BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00900001DA51D6E0E BOSCH MEVD17.2.9
0000190101310100001C9F1D6402 1.98.00600001CAE1D6405 BOSCH MEVD17.2.9
0000190101310100001C9F1D6402 1.98.00900001DA51D6407 BOSCH MEVD17.2.9
0000190101310100001C9F1D6402 1.98.00500001CE31D6402 BOSCH MEVD17.2.9
0000190101310100001C9F1D8201 1.94.00400001CE31D8205 BOSCH MEVD17.2.9
0000190101310100001C9F1D8201 1.94.00800001DA51D820D BOSCH MEVD17.2.9
0000190101310100001C9F1D8201 1.94.00800001DA51D8209 BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00900001CE31D6E03 BOSCH MEVD17.2.9
0000190101310100001C9F1D6E02 1.98.00900001DA51D6E03 BOSCH MEVD17.2.9
0000190101310200001C9F1D9601 1.94.00400001DA51D9603 BOSCH MEVD17.2.9
0000190101310200001C9F1D9601 1.94.00300001CE31D9607 BOSCH MEVD17.2.9
0000190101310200001C9F1D9601 1.94.00300001DA51D9607 BOSCH MEVD17.2.9
000019A7011301000019A8138C01 1.98.003000018A6138C07 BOSCH MEVD17.2.9
000019A7011301000019A813AA01 1.94.005000018A613AA0B BOSCH MEVD17.2.9
000019A7011301000019A8138201 1.98.003000018A6138204 BOSCH MEVD17.2.9
000019A7011301000019A813AA01 1.94.002000018A613AA0C BOSCH MEVD17.2.9

ECU-notities

MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata