AUDI S4 (8H/B7/8E) 4.2L V8 32V 309kW/414HP ME7.1.1

ECU BOSCH ME7.1.1 · 420 CV (309 kW) · 4200 cc · Benzina aspirato

ECU-databaseAUDI › AUDI S4 (8H/B7/8E) 4.2L V8 32V 309kW/414HP ME7.1.1

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 13 firmwareversies

Voertuiggegevens

MerkAUDI
ModelS4 (8H/B7/8E)
Motor4.2L V8 32V 309kW/414HP ME7.1.1
Standaard vermogen420 CV / 309 kW
Cilinderinhoud4200 cc
BrandstofBenzina aspirato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelME7.1.1
Geheugen / EPROM29F800 PSOP44 8Mbit - Flash 512K x 16

Beschikbare tuning-opties:

  • Advance at part load
  • Load / throttle position reference
  • Injection at part load
  • Advance limiter
  • Torque limiter
  • Lambda enrichment for components protection
  • Knock detection factor
  • Air mass flow

Firmware-identificatoren (13)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
02612011131037376347 1.42.0108E0910560T 0010 BOSCH ME7.1.1
02612013581037381476 1.84.0098E2910560B 0010 BOSCH ME7.1.1
02612013591037381475 1.84.0148E2910560C 0010 BOSCH ME7.1.1
02612018721037389414 1.84.0128E2910560G 0010 BOSCH ME7.1.1
02612084421037372812 1.42.0138E0910560J 0010 BOSCH ME7.1.1
02612084421037376349 1.42.0088E0910560J 0020 BOSCH ME7.1.1
02612084431037374043 1.42.0078E0910560K 0010 BOSCH ME7.1.1
02612084451037374042 1.42.0038E0910560M 0010 BOSCH ME7.1.1
02612084461037372814 1.42.0058E0910560N 0001 BOSCH ME7.1.1
02612084471037372810 1.42.0188E0910560P 0010 BOSCH ME7.1.1
02612088521037380111 1.84.0068E2910560 0030 BOSCH ME7.1.1
02612088531037380113 1.84.0138E2910560A 0030 BOSCH ME7.1.1
02612088551037376227 1.84.0088H2910560A 0010 BOSCH ME7.1.1

Technische voertuignotities

OBD located under the steering column, above the pedals. Visible or hidden by a plastic lid.

ECU-notities

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. On this epron can be set a KEY. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This Setting File can be used for serial system NewGenius. Attention! If you use the serial system: before start the program, disconnect the feeding on the fans radiator.