AUDI Q3 (F3) 35 1.5L 16V L4 TFSI 110kW/148HP MG1CS011 TC298

ECU BOSCH MG1CS011 · 150 CV (11 kW) · 1500 cc · Benzina sovralimentato

ECU-databaseAUDI › AUDI Q3 (F3) 35 1.5L 16V L4 TFSI 110kW/148HP MG1CS011 TC298

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 4 firmwareversies

Voertuiggegevens

MerkAUDI
ModelQ3 (F3)
Motor35 1.5L 16V L4 TFSI 110kW/148HP MG1CS011 TC298
Standaard vermogen150 CV / 11 kW
Cilinderinhoud1500 cc
BrandstofBenzina sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelMG1CS011
Geheugen / EPROMMicro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte

Beschikbare tuning-opties:

  • Base timing
  • Advance at idle speed
  • Minimum advance allowed
  • Optimal spark timing/MBT
  • Optimal spark timing/MBT 2
  • Knock correction advance max
  • Boost pressure limit control
  • Boost pressure limit control 2
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Maximum torque limitation at clutch
  • Maximum torque limitation at clutch 2
  • Compressor pressure ratio limit for pumping and speed
  • Compression ratio limiting for compressor depending on IAT sensor
  • Max accepted exhaust gas temperature at exhaust manifold
  • Max accepted exhaust gas pressure at exhaust manifold
  • Exhaust gas temperature
  • Minimum factor for air charge limitation
  • Air charge offset to enable limitation
  • Protection for engine overheating
  • Exhaust valves lift
  • Max torque correction factor for APS sensor
  • Engine torque reducing factor depending on temperature
  • Max CAT temperature threshold for component protection
  • Engine idle vs. ECT sensor
  • Gearbox maximum torque allowed
  • High pressure fuel pump setpoint
  • High fuel pressure pump limit for ECT sensor
  • Intake valve lift
  • L
  • Advance limiter for component protection 1
  • Boost pressure deviation limits for basic charge air pressure
  • Torque limiter
  • Lambda enrichment for components protection
  • Component protection activation delay
  • Lambda minimum value for components protection
  • Lambda value for components protection activation
  • Lambda correction for exhaust manifold temperature
  • RPM Limiter
  • RPM Limiter 2
  • RPM limiter 3
  • RPM Limiter 5
  • RPM limiter - N
  • RPM limiter in Park position
  • RPM limit for ECT sensor
  • RPM limit for EOT sensor
  • Low pressure fuel pump limit
  • Low pressure fuel pump limit for fuel mass flow
  • Low pressure fuel pump for EFT sensor
  • Lambda driver wish
  • Driver torque request limiter
  • Knock detection factor
  • Speed limiter
  • Cruise control speed limiter
  • Maximum indicated torque
  • Maximum engine air charge value
  • Maximum engine temperature for torque limitation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Maximum intake manifold pressure
  • Max torque profile
  • Optimal engine moment
  • Protection for oil overheating
  • Power limit torque table
  • Turbo pressure variation control factor
  • Turbo pressure variation control factor 2
  • Revolution limiter
  • Driver torque request
  • Driver torque request 2
  • Setpoint maximum turbocharger speed
  • Target Lambda for knock protection
  • Torque limiter in recovery mode
  • Torque limiter in recovery mode 2
  • Torque limiter in recovery mode 3
  • Torque limiter in recovery mode 4
  • Torque limiter in recovery mode 5

Firmware-identificatoren (4)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
1.02.00805E906018CP 1317 BOSCH MG1CS011
1.02.01205E906018N 9970 BOSCH MG1CS011
1.02.01805E906018CP 1014 BOSCH MG1CS011
1.02.01605E906018N 9866 BOSCH MG1CS011

Technische voertuignotities

OBD located under the steering column, above the pedals. Visible or hidden by a plastic lid.
ECU located in the engine bay behind/close to the battery. Difficulty: easy

ECU-notities

Micro Infineon Tricore TC298TP To work on this ECU you can use NewTrasdata