AUDI A4 (B5/8D) 1.8L 16V TURBO 132kW/177HP PLCC Motronic

ECU BOSCH MOTRONIC M3.2 · 180 CV (132 kW) · 1800 cc · Benzina sovralimentato

ECU-databaseAUDI › AUDI A4 (B5/8D) 1.8L 16V TURBO 132kW/177HP PLCC Motronic

Vind de firmware-identificatoren (hardware-, software- en updatenummers), beschikbare tuning-opties en hoe je het originele of geremapte bestand krijgt.

✓ Tuning via bestand (flash) 12 firmwareversies

Voertuiggegevens

MerkAUDI
ModelA4 (B5/8D)
Motor1.8L 16V TURBO 132kW/177HP PLCC Motronic
Standaard vermogen180 CV / 132 kW
Cilinderinhoud1800 cc
BrandstofBenzina sovralimentato
VoertuigtypeAuto

ECU

FabrikantBOSCH
ModelMOTRONIC M3.2
Geheugen / EPROM27C010 DIL32/PLCC32 1Mbit - Eprom 128K x 8

Beschikbare tuning-opties:

  • Advance at part load
  • Advance full load
  • Boost pressure limiter
  • Boost pressure limiter 2
  • Boost pressure limiter 3
  • Boost pressure
  • Injection at part load
  • RPM Limiter
  • Pressure control F (RPM)
  • Boost at full throttle
  • Air mass flow
  • Overboost timing

Firmware-identificatoren (12)

Hardware-nr.Software-nr. (chip)VersieUpdate-softwareECU
0261203550/12227355966 1.33.016 BOSCH MOTRONIC M3.2
02612035512227355966 1.33.009 BOSCH MOTRONIC M3.2
02612037601037355572 1.33.006 BOSCH MOTRONIC M3.2
02612041851037358703 1.33.032 BOSCH MOTRONIC M3.82
02612041851037358761 1.33.040 BOSCH MOTRONIC M3.82
02612041851037355888 1.33.029 BOSCH MOTRONIC M3.82
02612048051037360270 1.33.004 BOSCH MOTRONIC M3.82
02612048051037358123 1.33.019 BOSCH MOTRONIC M3.82
02612064291037350714 1.33.021 BOSCH MOTRONIC M3.82
02612047781037358150 1.33.031 BOSCH MOTRONIC M3.82 DAMOS 30 N
02612041851037355482 1.33.030 BOSCH MOTRONIC M3.82 DAMOS 30Z
02612048051037315606 1.33.010 BOSCH MOTRONIC M3.82 Damos 3N2

ECU-notities

Original EPROM 27C010 PLCC 32 pins To read this EPROM with the EMP20/21 programmer you need PD32 adapters.
Original EPROM 28F210 or 27C1024 PLCC 44 pins To read this EPROM with the EMP20/EMP21 programmer you need the PD44 adapters for PLCC 44 pins.
Original eprom PLCC 27C1024. Use adapter PD44 for the programmer and kit PLCC for the emulator.
Original EPROM 27C010 PLCC 32 pins To read this EPROM with the EMP20/21 programmer you need PD32 adapters. Put all the map of the Boost F (Temep 1 and 2) to 255 to erase the Boost limiter.