Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 3 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | VOLKSWAGEN |
| Modelis | PHAETON |
| Variklis | 3.0L V6 TDI 165kW/225HP EDC16+ |
| Serijinė galia | 225 CV / 166 kW |
| Darbinis tūris | 3000 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | EDC16U31/U34/CP34 |
| Atmintis / EPROM | M58BW016DB PQFP80 - Flash 3_V 512 x 32 |
Galimos derinimo operacijos / parinktys:
- Main injection duration angle
- Main injection duration angle 2
- Main injection duration angle 3
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure in aftertreatment modes
- EGR valve control
- EGR valve control 2
- EGR valve control in aftertreatment modes
- EGR valve control in aftertreatment modes 2
- Exhaust gas temperature
- Protection for engine overheating
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Engine idle vs. ECT sensor 2
- Engine idle vs. ECT sensor 3
- Gearbox maximum torque allowed
- Maximum injection period
- Injection opening time related to inj. pressure
- Injection 1
- Injection in aftertreatment modes 1
- L
- Torque limiter
- Smoke limiter
- RPM limiter - fuel cut
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation in aftertreatment modes
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature for O2
- LSU temperature threshold PID heater governor activation
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Air mass flow
- CAT downstream temperature sensor characterization
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for selected gear
- Torque limiter for for reverse gear
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Torque limiter in recovery mode 2
- Torque limiter in recovery mode 3
- Volumetric efficiency
- Volumetric efficiency - correction
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
Programinės įrangos identifikatoriai (3)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | 1037374420 |
1.67.026 | 3D0907401 0030 |
BOSCH EDC16U31/U34/CP34 |
| — | 1037381551 |
1.67.032 | 3D0907401A 0010 |
BOSCH EDC16U31/U34/CP34 |
| — | 1037375570 |
1.67.046 | 3D0907401 0040 |
BOSCH EDC16U31/U34/CP34 |
ECU pastabos
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4. This Setting File can be used for serial programming system NewGenius. To modify this Ecu you can use the BDM system:555PRO or TRASDATA. WARNING:TRASDATA DO NOT need additional tools, 555PRO instead requires recalculation chks with VAG EDC16 CHECKSUM tool supplied with 555PRO, otherwise you will cause the block of the ecu or the detection of a change in the Ecu through diagnostic tool.
Galimi papildomi moduliai
A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
