Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 15 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | SKODA |
| Modelis | SUPERB (B6) |
| Variklis | 1.8L 16V TSI 118kW/158HP MED17.5 |
| Serijinė galia | 160 CV / 118 kW |
| Darbinis tūris | 1800 cc |
| Kuras | Benzina sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MED17.5 |
| Atmintis / EPROM | MICRO ST TRICORE - 12032 Kbit - 178000 |
Galimos derinimo operacijos / parinktys:
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Optimal spark timing/MBT
- Advance correction
- Height correction for boost pressure
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Maximum pressure ratio limit for diagnosis
- Exhaust gas temperature
- Filling factor limit
- Filling factor limit 2
- Factor for reducing maximum filling
- Gearbox maximum torque allowed
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- High fuel pressure pump limit
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- Torque limiter at high EGT
- RPM Limiter
- Lambda driver wish
- Knock detection factor
- Maximum boost pressure load
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Optimal engine moment
- Power limit torque table
- Relative permissible torque from the pedal position in torque limitation
- Relative permissible torque from the pedal position in torque limitation - sport/race mode
- Pressure ratio depending on IAT
- Maximum pressure ratio limit depending on temperature
- Driver torque request
- Driver torque request AWD
- Driver torque request for reverse gear
- Exhaust gas temperature sensor
- Throttle angle management
Programinės įrangos identifikatoriai (15)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | — |
1.94.012 | 3T0907115 0050 |
BOSCH MED17.5 |
| — | — |
1.94.017 | 3TD906264 0060 |
BOSCH MED17.5 |
| — | — |
1.94.011 | 3T0907115C 0020 |
BOSCH MED17.5 |
| — | — |
1.94.006 | 3T0907115G 0040 |
BOSCH MED17.5 |
| — | — |
1.94.007 | 3T0907115H 0040 |
BOSCH MED17.5 |
| — | — |
1.94.009 | 3T0907115 0030 |
BOSCH MED17.5 |
| — | — |
1.94.004 | 3TD906264 0070 |
BOSCH MED17.5 |
| — | — |
1.94.009 | 3T0907115N 0010 |
BOSCH MED17.5 |
| — | — |
1.94.012 | 1Z0907115R 0020 |
BOSCH MED17.5 |
| — | — |
1.94.012 | 1Z0907115J 0040 |
BOSCH MED17.5 |
| — | — |
1.94.014 | 3T0907115G 0010 |
BOSCH MED17.5 |
| — | — |
1.94.010 | 3T0907115M 0010 |
BOSCH MED17.5 |
| — | — |
1.94.011 | 3T0907115B 0030 |
BOSCH MED17.5 |
| — | — |
1.94.014 | 3T0907115E 0010 |
BOSCH MED17.5 |
| — | — |
1.94.013 | 3TD906264 0030 |
BOSCH MED17.5 |
ECU pastabos
MICRO Infineon Tricore TC1766 This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
