SKODA SUPERB (B5) 2.0L 16V TDI 103kW/138HP EDC16U31 — ECU BOSCH EDC16U31/U34/CP34

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) 5 programinės įrangos versijos

Gaukite failą šiai transporto priemonei

Pirkti failą (originalų arba perprogramuotą)Užsiregistruokite mastertuningfile.com ir užsisakykite failą

Esate servisas ar derintojas?

Transporto priemonės duomenys

Markė	SKODA
Modelis	SUPERB (B5)
Variklis	2.0L 16V TDI 103kW/138HP EDC16U31
Serijinė galia	140 CV / 103 kW
Darbinis tūris	2000 cc
Kuras	Diesel sovralimentato
Transporto priemonės tipas	Auto

ECU

Gamintojas	BOSCH
Modelis	EDC16U31/U34/CP34
Atmintis / EPROM	M58BW016DB PQFP80 - Flash 3_V 512 x 32

Galimos derinimo operacijos / parinktys:

Smoke limiter 2
Main injection duration angle
Main injection duration angle 4
Main injection duration angle 5
Boost pressure limiter
Maximum engine boost pressure F (atmospheric pressure)
Boost pressure
Boost pressure in aftertreatment modes
Boost pressure in aftertreatment modes 2
Boost pressure in aftertreatment modes 3
EGR valve control
EGR valve control in aftertreatment modes
EGR valve control in aftertreatment modes 2
EGR valve control in aftertreatment modes 3
EGR valve control in aftertreatment modes 4
EGR valve control in aftertreatment modes 5
EGR valve control in aftertreatment modes 6
Exhaust gas temperature
Protection for engine overheating
Basic torque management at engine cranking
Engine idle vs. ECT sensor
Gearbox maximum torque allowed
Injection period
Injection period - correction
Maximum injection period
Max injection limit - limp mode
J
Injection in aftertreatment modes 1
Torque limiter
Smoke limiter
RPM limiter - fuel cut
Lambda value of the smoke limitation
Lambda value of the smoke limitation in aftertreatment modes
Minimum LSU sensor temperature for O2
Maximum LSU sensor temperature for O2
LSU temperature threshold PID heater governor activation
Protection for air load overheating
Protection for exhaust gas temperature before turbine
Protection for fuel overheating
Protection for oil overheating
Air mass flow
Driver torque request
Driver torque request AWD
CAT downstream temperature sensor characterization
Torque limiter for the 1st gear selected
Torque limiter for the 2nd gear selected
Torque limiter for the 3rd gear selected
Torque limiter for the 4th gear selected
Torque limiter for the 5th gear selected
Torque limiter for the 6th gear selected
Torque limiter for selected gear
Torque limiter for for reverse gear
Torque limiter for the APS/BPS
Torque limiter in recovery mode
Torque limiter in recovery mode 2
Volumetric efficiency
Turbocharger volumetric efficiency
Variable geometry duty cycle limit
Variable geometry duty cycle limit 2
Variable geometry duty cycle limit 3

Programinės įrangos identifikatoriai (5)

Aparatinės įrangos Nr.	Programinės įrangos Nr. (lustas)	Versija	Atnaujinimo programinė įranga	ECU
—	1037378316	1.67.010	03G906016G 8203	BOSCH EDC16U31/U34/CP34
—	1037387088	1.67.012	03G997019P 1097	BOSCH EDC16U31/U34/CP34
—	1037395411	1.67.025	03G906021QP 2893	BOSCH EDC16U31/U34/CP34
—	1037378316	1.67.041	03G906016GT 8203	BOSCH EDC16U31/U34/CP34
—	1037387090	1.67.027	03G906016GT 9780	BOSCH EDC16U31/U34/CP34

ECU pastabos

This Setting File can be used for serial programming system NewGenius. The only way to modify this ECU is by using the BDM system: TRASDATA or NEW TRASDATA. To modify this Ecu you can use the BDM system:555PRO or TRASDATA. WARNING:TRASDATA DO NOT need additional tools, 555PRO instead requires recalculation chks with VAG EDC16 CHECKSUM tool supplied with 555PRO, otherwise you will cause the block of the ecu or the detection of a change in the Ecu through diagnostic tool. Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4.

Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4. This Setting File can be used for serial programming system NewGenius. To work on this ECU you can use NewTrasdata To modify this Ecu you can use the BDM system:555PRO or TRASDATA. WARNING:TRASDATA DO NOT need additional tools, 555PRO instead requires recalculation chks with VAG EDC16 CHECKSUM tool supplied with 555PRO, otherwise you will cause the block of the ecu or the detection of a change in the Ecu through diagnostic tool.

Gaukite failą šiai transporto priemonei

Pirkti failą (originalų arba perprogramuotą)Užsiregistruokite mastertuningfile.com ir užsisakykite failą Esate servisas ar derintojas?Siūlykite šias paslaugas patys: aktyvuokite savo TuningFile platformą

Tools to read and write this ECU

Flex Programmatore per rimappatura centraline e cambi automatici ECU + auto gearbox € 1.000 Buy

The Genius OBD + Bench € 2.500 Buy

Kiti SKODA

FELICIA Mk1/Mk2
1.3L OCTAVIA (1U)
1.8L 20V 125HP PSOP M3.8.3 FORMAN
1.3L 8V 40kW/54HP MOTRONIC OCTAVIA (1U)
1.9L 8V TDI 81kW/110HP EDC15 V/VM/VM+ FELICIA Mk1/Mk2
1.6L OCTAVIA (1U)
1.6L 8V 55kW/75HP IAW1AV OCTAVIA (1U)
1.8L 20V TURBO 110kW/150HP M3.8.3 OCTAVIA (1U)
2.0L 8V 85kW/115HP M5.92 FABIA Mk1 (6Y)
1.4L 16V 75/101HP IAW 4LV/4MV FABIA Mk1 (6Y)
1.4L 8V MPI 51kW/68HP SIMOS3

→ Visos ECU SKODA