PORSCHE BOXSTER (987) 3.4L RS60 223kW/303HP ME7.8.1

ECU BOSCH ME7.8.1 · 303 CV (223 kW) · 3400 cc · Benzina aspirato

ECU duomenų bazėPORSCHE › PORSCHE BOXSTER (987) 3.4L RS60 223kW/303HP ME7.8.1

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) ✓ Galimas papildomas modulis 3 programinės įrangos versijos

Transporto priemonės duomenys

MarkėPORSCHE
ModelisBOXSTER (987)
Variklis3.4L RS60 223kW/303HP ME7.8.1
Serijinė galia303 CV / 223 kW
Darbinis tūris3400 cc
KurasBenzina aspirato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisME7.8.1
Atmintis / EPROM29F800 PSOP44 8Mbit - Flash 512K x 16

Galimos derinimo operacijos / parinktys:

  • Base timing
  • Minimum advance allowed
  • Optimal spark timing/MBT
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Exhaust gas temperature
  • Factor to correct fuel delivery system
  • Factor to correct fuel delivery system 2
  • HFM/HLM air flow high limit
  • HFM/HLM air flow low limit
  • Lambda enrichment for components protection
  • Torque limiter at high EGT
  • Lambda efficiency
  • RPM Limiter
  • RPM limiter in Park position
  • Lambda driver wish
  • Knock detection factor
  • MAF sensor calibration
  • Maximum indicated torque
  • Maximum ignition delay allowed for knock limiter intervention
  • Maximum possible engine charge
  • Throttle air mass flow calculation
  • Minimum engine air charge value
  • Number of injections considered for knock limitation
  • Optimal engine moment
  • Offset tolerance depending on permissible torque
  • Relative permissible torque from the pedal position in torque limitation
  • Relative permissible torque from the pedal position in torque limitation - sport/race mode
  • Relative permissible torque from the pedal position in torque limitation - sport/race mode 2
  • Driver wish
  • Driver torque request
  • Driver torque request for reverse gear
  • Driver torque request Sport mode
  • Maximum threshold for detecting engine knock - bank 1
  • Maximum threshold for detecting engine knock - bank 2
  • Throttle angle management
  • Variable intake pulsation correction

Programinės įrangos identifikatoriai (3)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
02612079871037379149 1.27.0060041900007605D08 BOSCH ME7.8.1
02612079871037379149 1.27.0030041900007605D18 BOSCH ME7.8.1
02612083001037379150 1.27.00400419100A8615D0R BOSCH ME7.8.1

ECU pastabos

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. This Setting File can be used for serial system NewGenius. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!

Galimi papildomi moduliai

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

→ See all add-on modules on the shop