MINI F55/F56/F57 2.0L L4 16V COOPER SD 140kW/188HP EDC17C50

ECU BOSCH EDC17C50 · 190 CV (14 kW) · 2000 cc · Diesel sovralimentato

ECU duomenų bazėMINI › MINI F55/F56/F57 2.0L L4 16V COOPER SD 140kW/188HP EDC17C50

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) ✓ Galimas papildomas modulis 5 programinės įrangos versijos

Transporto priemonės duomenys

MarkėMINI
ModelisF55/F56/F57
Variklis2.0L L4 16V COOPER SD 140kW/188HP EDC17C50
Serijinė galia190 CV / 14 kW
Darbinis tūris2000 cc
KurasDiesel sovralimentato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisEDC17C50
Atmintis / EPROMMICRO ST TRICORE - 32768 Kbit - 400000

Galimos derinimo operacijos / parinktys:

  • Boost pressure limiter
  • Boost pressure
  • EGR valve control
  • EGR valve control 2
  • EGR valve control 3
  • EGR valve control 4
  • EGR valve control 5
  • EGR valve control 6
  • Max accepted exhaust gas temperature value at particulate sensor
  • Exhaust gas temperature threshold for component protection
  • Protection for engine overheating
  • Protection for engine overheating 2
  • Protection for engine overheating 3
  • Basic torque management at engine cranking
  • Injection period
  • Maximum injection period
  • Injection opening time related to inj. pressure
  • Initialization values over pressure control valve
  • J
  • L
  • Torque limiter 3
  • Torque limiter 4
  • Torque limiter 5
  • Boost pressure deviation limits for basic charge air pressure
  • Boost pressure deviation limits for basic charge air pressure 2
  • Torque limiter
  • Torque limiter for diagnostic
  • Torque limiter for diagnostic 2
  • Torque limiter during particulate filter overloading - pressure
  • Torque limiter during particulate filter overloading - temperature
  • Lambda value of the smoke limitation
  • Minimum LSU sensor temperature limit - heater control
  • Minimum LSU sensor temperature for O2
  • Maximum LSU sensor temperature limit - heater control
  • Maximum LSU sensor temperature for O2
  • LSU temperature setpoint
  • LSU temperature threshold PID heater governor activation
  • Speed limiter
  • Maximum indicated torque
  • Maximum engine torque at crank shaft
  • Pressure control map over pressure regulating valve
  • Specific injection pressure limiter
  • Specific injection pressure limiter 2
  • Specific injection pressure limiter 3
  • Relative permissible torque from the pedal position in torque limitation
  • Specific injection pressure
  • Specific injection pressure 2
  • Specific injection pressure 3
  • Driver torque request
  • CAT upstream temperature sensor characterization
  • DPF upstream temperature sensor characterization
  • SCR upstream temperature sensor characterization
  • Torque limiter for the 1st gear selected
  • Torque limiter for the 2nd gear selected
  • Torque limiter for the 3rd gear selected
  • Torque limiter for the 4th gear selected
  • Torque limiter for the 5th gear selected
  • Torque limiter for the 6th gear selected
  • Torque limiter for the 7th gear selected
  • Torque limiter for the 8th gear selected
  • Torque limiter for the 9th gear selected
  • Torque limiter for for reverse gear
  • Torque limiter for EFT sensor
  • Torque limiter in recovery mode
  • Turbocharger volumetric efficiency
  • Variable geometry duty cycle limit

Programinės įrangos identifikatoriai (5)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
00000A0A061C0000000A0B701000 1.00.00700003A13701005 BOSCH EDC17C50
00000A0A061C0000000A0B701100 1.00.01300003B8870110A BOSCH EDC17C50
00000A0A061C0000000A0B701000 1.00.022000027D4701005 BOSCH EDC17C50
00000A0A061C0000000A0B701300 1.00.01100003792701304 BOSCH EDC17C50
00000A0A061C0000000A0B701600 1.00.01300002AED701609 BOSCH EDC17C50

ECU pastabos

MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata