MERCEDES GLC CLASS X253 GLC300 2.0L 16V TURBO 180kW/241HP MED17.7.2

ECU BOSCH MED17.7.2 · 245 CV (18 kW) · 2000 cc · Benzina sovralimentato

ECU duomenų bazėMERCEDES › MERCEDES GLC CLASS X253 GLC300 2.0L 16V TURBO 180kW/241HP MED17.7.2

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) ✓ Galimas papildomas modulis 7 programinės įrangos versijos

Transporto priemonės duomenys

MarkėMERCEDES
ModelisGLC CLASS X253
VariklisGLC300 2.0L 16V TURBO 180kW/241HP MED17.7.2
Serijinė galia245 CV / 18 kW
Darbinis tūris2000 cc
KurasBenzina sovralimentato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisMED17.7.2
Atmintis / EPROMMICRO ST TRICORE - 32768 Kbit - 400000

Galimos derinimo operacijos / parinktys:

  • Absolute boost limit
  • Maximum air charge for overboost protection with turbocharger fault
  • Base timing
  • Optimal spark timing/MBT
  • Ambient pressure threshold for boost diagnosis
  • Advance correction
  • Advance correction 2
  • Torque value while scavenging
  • Boost pressure limiter 2
  • Boost pressure
  • Boost pressure 2
  • Height correction for boost pressure
  • Desired engine load calculation
  • Compression ratio for turbocharger protection
  • Delta pressure for charging protection over diagnosis
  • Desired pressure ratio
  • Desired pressure ratio in Sport mode
  • Exhaust gas temperature
  • Maximum value for EKP (electric fuel pump)
  • Factor to correct fuel delivery system
  • Factor for reducing maximum filling
  • Gearbox maximum torque allowed
  • Maximum value for HDP (high pressure fuel pump)
  • High pressure fuel pump setpoint
  • L
  • Torque limiter for diagnostic
  • Lambda enrichment for components protection
  • Lambda correction for exhaust manifold temperature
  • Torque limiter at high EGT
  • RPM Limiter
  • RPM Limiter 2
  • RPM limiter - AT
  • Engine speed limit at high oil temperature
  • Boost pressure linearization
  • Lambda driver wish
  • Knock detection factor
  • Speed limiter
  • Maximum indicated torque
  • Boost pressure minimal delta
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Max injection amount for each cylinder
  • Maximum intake manifold pressure
  • Maximum negative deviation for boost overcharge
  • Max torque profile
  • Max torque profile (overboost active)
  • Optimal engine moment
  • Boost pressure threshold cycles for the overboost recognition
  • Torque/load reduction for overheating protection
  • Power limit torque table
  • Pressure ratio depending on IAT
  • Maximum pressure ratio limit depending on temperature
  • Specific air mass flow quantity limiter
  • % relative air filling limit depending on IAT
  • Driver torque request
  • Torque limiter for the 1st gear selected
  • Torque limiter for selected gear
  • Torque limiter for selected gear 2
  • Throttle angle management
  • Transmission torque limit - clutch disengaged
  • Transmission torque limit - clutch disengaged . ESP deactivated
  • Transmission torque limit - clutch disengaged - reverse gear engaged
  • Transmission torque limitation at gs-messages interruption
  • Turbocharger volumetric efficiency

Programinės įrangos identifikatoriai (7)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
27090407002749021801 1.94.0062749036704 BOSCH MED17.7.2
27090407002749026801 1.94.0122749032905 BOSCH MED17.7.2
27090407002749023901 1.94.0112749033904 BOSCH MED17.7.2
27090407002749029900 1.94.0072749033603 BOSCH MED17.7.2
27090407002749021801 1.94.0052749031504 BOSCH MED17.7.2
27090407002749020801 1.94.0062749035203 BOSCH MED17.7.2
27090407002749026101 1.94.0162749031305 BOSCH MED17.7.2

ECU pastabos

MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata

Galimi papildomi moduliai

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

→ See all add-on modules on the shop