MERCEDES E CLASS W213 E320 3.0L V6 24V BITURBO 200kW/268HP MED17.7.3.1

ECU BOSCH MED17.7.3.1 · 272 CV (2 kW) · 3000 cc · Benzina sovralimentato

ECU duomenų bazėMERCEDES › MERCEDES E CLASS W213 E320 3.0L V6 24V BITURBO 200kW/268HP MED17.7.3.1

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) ✓ Galimas papildomas modulis 1 programinės įrangos versijos

Transporto priemonės duomenys

MarkėMERCEDES
ModelisE CLASS W213
VariklisE320 3.0L V6 24V BITURBO 200kW/268HP MED17.7.3.1
Serijinė galia272 CV / 2 kW
Darbinis tūris3000 cc
KurasBenzina sovralimentato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisMED17.7.3.1
Atmintis / EPROMMicro TC1797+ Flash esterna S29CD016G

Galimos derinimo operacijos / parinktys:

  • Maximum air charge for overboost protection with turbocharger fault
  • Base timing
  • Optimal spark timing/MBT
  • Boost pressure limiter
  • Height correction for boost pressure
  • Desired engine load calculation
  • Compression ratio for turbocharger protection
  • Exhaust gas temperature
  • Maximum value for EKP (electric fuel pump)
  • Factor to correct fuel delivery system
  • Factor for reducing maximum filling
  • Maximum value for HDP (high pressure fuel pump)
  • High pressure fuel pump setpoint
  • High pressure fuel pump setpoint 2
  • Lambda enrichment for components protection
  • Lambda correction for exhaust manifold temperature
  • Torque limiter at high EGT
  • RPM Limiter
  • RPM Limiter 2
  • RPM limiter 3
  • RPM limit for EOT sensor
  • Lambda driver wish
  • Knock detection factor
  • Speed limiter
  • MAF sensor calibration
  • Maximum compression ratio
  • Throttle air mass flow calculation
  • Manifold absolute pressure time delay
  • Characteristic manifold absolute pressure time constant of the LRS
  • Max injection amount for each cylinder
  • Maximum negative deviation for boost overcharge
  • Max torque profile
  • Optimal engine moment
  • Torque/load reduction for overheating protection
  • Pressure ratio depending on IAT
  • Specific air mass flow quantity limiter
  • % relative air filling limit depending on IAT
  • Throttle angle management
  • Turbocharger volumetric efficiency

Programinės įrangos identifikatoriai (1)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
00090410002769028100 1.94.0082769033402 BOSCH MED17.7.3.1

ECU pastabos

MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata

Galimi papildomi moduliai

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

→ See all add-on modules on the shop