Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 10 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | MERCEDES |
| Modelis | E CLASS W213 |
| Variklis | E300 2.0L 16V TURBO 180kW/241HP MED17.7.2 |
| Serijinė galia | 245 CV / 18 kW |
| Darbinis tūris | 2000 cc |
| Kuras | Benzina sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MED17.7.2 |
| Atmintis / EPROM | MICRO ST TRICORE - 32768 Kbit - 400000 |
Galimos derinimo operacijos / parinktys:
- Absolute boost limit
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Base timing - full load
- Optimal spark timing/MBT
- Ambient pressure threshold for boost diagnosis
- Advance correction
- Torque value while scavenging
- Boost pressure limiter 2
- Boost pressure
- Boost pressure 2
- Height correction for boost pressure
- Desired engine load calculation
- Compression ratio for turbocharger protection
- Delta pressure for charging protection over diagnosis
- Desired pressure ratio
- Desired pressure ratio in Sport mode
- Exhaust gas temperature
- Maximum value for EKP (electric fuel pump)
- Factor to correct fuel delivery system
- Factor for reducing maximum filling
- Gearbox maximum torque allowed
- Maximum value for HDP (high pressure fuel pump)
- High pressure fuel pump setpoint
- L
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- Torque limiter at high EGT
- RPM Limiter
- RPM Limiter 2
- RPM limiter - AT
- Engine speed limit at high oil temperature
- Lambda driver wish
- Knock detection factor
- Speed limiter
- Boost pressure minimal delta
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Max injection amount for each cylinder
- Maximum intake manifold pressure
- Maximum negative deviation for boost overcharge
- Max torque profile
- Max torque profile (overboost active)
- Optimal engine moment
- Boost pressure threshold cycles for the overboost recognition
- Torque/load reduction for overheating protection
- Power limit torque table
- Pressure ratio depending on IAT
- Maximum pressure ratio limit depending on temperature
- Specific air mass flow quantity limiter
- % relative air filling limit depending on IAT
- Throttle angle management
- Turbocharger volumetric efficiency
Programinės įrangos identifikatoriai (10)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| 2709040700 | 2749023101 |
1.94.006 | 2749038404 |
BOSCH MED17.7.2 |
| 2709040700 | 2749024301 |
1.94.010 | 2749034704 |
BOSCH MED17.7.2 |
| 2709040700 | 2749026901 |
1.94.003 | 2749033205 |
BOSCH MED17.7.2 |
| 2709040700 | 2749029500 |
1.94.037 | 2749039903 |
BOSCH MED17.7.2 |
| 2709040700 | 2749026500 |
1.94.020 | 2749032203 |
BOSCH MED17.7.2 |
| 2709040700 | 2749023101 |
1.94.013 | 2749032504 |
BOSCH MED17.7.2 |
| 2709040700 | 2749024501 |
1.94.006 | 2749035604 |
BOSCH MED17.7.2 |
| 2709040700 | 2749024301 |
1.94.008 | 2749034704 |
BOSCH MED17.7.2 |
| 2709040700 | 2749024501 |
1.94.009 | 2749036904 |
BOSCH MED17.7.2 |
| 2709040700 | 2749029500 |
1.94.006 | 2749030703 |
BOSCH MED17.7.2 |
ECU pastabos
MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
