Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 7 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | MERCEDES |
| Modelis | C CLASS W205 |
| Variklis | C400 3.0L V6 24V BITURBO 245kW/329HP MED17.7.3.1 |
| Serijinė galia | 333 CV / 245 kW |
| Darbinis tūris | 3000 cc |
| Kuras | Benzina sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MED17.7.3.1 |
| Atmintis / EPROM | Micro TC1797+ Flash esterna S29CD016G |
Galimos derinimo operacijos / parinktys:
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Optimal spark timing/MBT
- Height correction for boost pressure
- Desired engine load calculation
- Compression ratio for turbocharger protection
- Desired pressure ratio
- Exhaust gas temperature
- Maximum value for EKP (electric fuel pump)
- Factor to correct fuel delivery system
- Factor for reducing maximum filling
- Maximum value for HDP (high pressure fuel pump)
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- Advance limiter
- Torque limiter for diagnostic
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- Torque limiter at high EGT
- Max desired pressure ratio limit
- Max desired pressure ratio limit (Sport mode)
- RPM Limiter
- RPM limit for EOT sensor
- Boost pressure linearization
- Lambda driver wish
- Knock detection factor
- Speed limiter
- MAF sensor calibration
- Maximum indicated torque
- Maximum boost pressure load
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Max injection amount for each cylinder
- Maximum negative deviation for boost overcharge
- Max torque profile
- Optimal engine moment
- Torque/load reduction for overheating protection
- Power limit torque table
- Pressure ratio depending on IAT
- Maximum pressure ratio limit depending on temperature
- Specific air mass flow quantity limiter
- % relative air filling limit depending on IAT
- Driver torque request
- Throttle angle management
- Turbocharger volumetric efficiency
Programinės įrangos identifikatoriai (7)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| 0009041000 | 2769020901 |
1.94.011 | 2769036303 |
BOSCH MED17.7.3.1 |
| 0009041000 | 2769026600 |
1.94.013 | 2769037201 |
BOSCH MED17.7.3.1 |
| 0009041000 | 2769029800 |
1.94.013 | 2769037802 |
BOSCH MED17.7.3.1 |
| 0009041000 | 2769025700 |
1.94.011 | 2769038101 |
BOSCH MED17.7.3.1 |
| 0009041000 | 2769027500 |
1.94.006 | 2769033302 |
BOSCH MED17.7.3.1 |
| 0009041000 | 2769025300 |
1.94.043 | 2769037801 |
BOSCH MED17.7.3.1 |
| 0009041000 | 2769020801 |
1.94.007 | 2769036203 |
BOSCH MED17.7.3.1 |
ECU pastabos
MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
