IVECO UNIECO 3.0L 80kW/107HP EDC16C39

ECU BOSCH EDC16C39 · 109 CV (8 kW) · 3000 cc · Diesel sovralimentato

ECU duomenų bazėIVECO › IVECO UNIECO 3.0L 80kW/107HP EDC16C39

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) 1 programinės įrangos versijos

Transporto priemonės duomenys

MarkėIVECO
ModelisUNIECO
Variklis3.0L 80kW/107HP EDC16C39
Serijinė galia109 CV / 8 kW
Darbinis tūris3000 cc
KurasDiesel sovralimentato
Transporto priemonės tipasTir

ECU

GamintojasBOSCH
ModelisEDC16C39
Atmintis / EPROMM58BW016DB PQFP80 - Flash 3_V 512 x 32

Galimos derinimo operacijos / parinktys:

  • Maximum engine boost pressure F (atmospheric pressure)
  • Boost pressure
  • EGR valve control
  • Exhaust gas temperature
  • Protection for engine overheating
  • Basic torque management at engine cranking
  • Engine idle vs. ECT sensor
  • Injection period
  • Injection opening time related to inj. pressure
  • Max injection limit
  • Max injection limit for APS/BPS sensor
  • Fuel quantity limitation after cold start
  • Max injection limit - limp mode
  • J
  • Injection 2
  • Torque limiter 2
  • Torque limiter 3
  • Boost pressure deviation limits for basic charge air pressure
  • Boost pressure deviation limits for basic charge air pressure 2
  • Torque limiter
  • Lambda value of the smoke limitation
  • Minimum LSU sensor temperature limit - heater control
  • Minimum LSU sensor temperature for O2
  • Maximum LSU sensor temperature limit - heater control
  • Maximum LSU sensor temperature for O2
  • LSU temperature threshold PID heater governor activation
  • Injection quantity for engine overheating protection
  • Injection quantity for engine overheating protection 3
  • Protection for fuel overheating
  • Protection for oil overheating
  • Pressure control map over pressure regulating valve
  • Specific injection pressure limiter
  • Specific injection pressure limiter 2
  • Specific injection pressure
  • Specific injection pressure in aftertreatment modes
  • Driver torque request
  • Torque limiter for the 1st gear selected
  • Torque limiter for the 2nd gear selected
  • Torque limiter for the 3rd gear selected
  • Torque limiter for the 4th gear selected
  • Torque limiter for the 5th gear selected
  • Torque limiter for the 6th gear selected
  • Torque limiter for selected gear
  • Torque limiter for for reverse gear
  • Torque limiter for the APS/BPS
  • Volumetric efficiency
  • Volumetric efficiency - correction
  • Turbocharger volumetric efficiency
  • Variable geometry duty cycle limit
  • Variable geometry duty cycle limit 2

Programinės įrangos identifikatoriai (1)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
02810121931037378086P_315V91 1.67.006C080280W4HFHNV91P15.HEX BOSCH EDC16C39

ECU pastabos

This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata