BMW X1 SERIES F48/F49 25iX 2.0L L4 16V 170kW/228HP DME_84T1

ECU BOSCH MG1CS201 (DME_84T1) · 231 CV (17 kW) · 2000 cc · Benzina sovralimentato

ECU duomenų bazėBMW › BMW X1 SERIES F48/F49 25iX 2.0L L4 16V 170kW/228HP DME_84T1

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) 1 programinės įrangos versijos

Transporto priemonės duomenys

MarkėBMW
ModelisX1 SERIES F48/F49
Variklis25iX 2.0L L4 16V 170kW/228HP DME_84T1
Serijinė galia231 CV / 17 kW
Darbinis tūris2000 cc
KurasBenzina sovralimentato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisMG1CS201 (DME_84T1)
Atmintis / EPROMMicro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte

Galimos derinimo operacijos / parinktys:

  • Base timing
  • Base timing 2
  • Camshaft maximum lift
  • Lambda/AFR full load/WOT
  • Lambda/AFR mixture at part load
  • Optimal spark timing/MBT
  • Optimal spark timing/MBT 2
  • Knock correction advance max
  • Boost pressure limiter for diagnostics
  • Maximum torque limitation at clutch
  • Desired pressure ratio
  • Max accepted exhaust gas temperature value after turbine
  • Max accepted exhaust gas pressure at exhaust manifold
  • Exhaust gas temperature 2
  • Exhaust gas temperature 3
  • Exhaust gas temperature 4
  • Max torque correction factor for knock sensor
  • Filling factor limit
  • Filling factor limit 2
  • Filling factor limit 3
  • Filling factor limit 4
  • Engine torque reducing factor depending on engine speed
  • Engine torque reducing factor depending on temperature
  • HFM/HLM threshold for diagnosis
  • HFM/HLM air flow high limit
  • HFM/HLM air flow low limit
  • High pressure fuel pump setpoint
  • High fuel pressure pump limit for ECT sensor
  • High fuel pressure pump limit 2
  • Intake pressure protection
  • Intake valve lift - cold
  • Intake valve lift - catalyst heating
  • Intake valve lift - start for ECT sensor
  • Intake valve lift - warm
  • Torque limiter 2
  • L
  • Torque limiter 4
  • Basic value Lambda sensor
  • Torque limiter
  • Lambda minimum value for components protection
  • Lambda fat-running limit for component protection
  • RPM limiter - AT
  • RPM limiter - MT
  • Low pressure fuel pump for EFT sensor
  • Knock detection factor
  • Speed limiter
  • Maximum indicated torque
  • Maximum compression ratio
  • Maximum possible engine charge
  • Maximum engine power
  • Maximum engine pressure ratio
  • Maximum relative engine air charge
  • Maximum rail pressure at start-up
  • Max torque profile - AT
  • Max torque profile - MT
  • Optimal engine moment
  • Pressure ratio depending on IAT
  • Pressure ratio depending on IAT 2
  • Driver torque request
  • Driver torque request Eco mode - AT
  • Driver torque request Eco mode - AT - 2
  • Driver torque request Normal mode - AT
  • Driver torque request Sport mode - AT
  • Driver torque request Sport mode - AT - 2
  • Driver torque request Eco mode
  • Driver torque request Eco mode - MT
  • Driver torque request Eco mode - MT - 2
  • Driver torque request Normal mode - MT
  • Driver torque request Sport mode - MT
  • Driver torque request Sport mode - MT - 2
  • Driver torque request Sport mode
  • Torque limiter for selected gear
  • Torque limiter for selected gear - AT
  • Start of injection
  • Maximum upper tolerance intake pressure protection
  • Torque limit table for IAT sensor
  • Lower pressure control threshold
  • Torque limiter to prevent preignition
  • Torque limiter in recovery mode
  • Torque limiter in recovery mode 2
  • Upper engine rpm threshold for diagnostic control
  • Upper pressure control threshold
  • Turbocharger volumetric efficiency
  • Wastegate duty-cycle

Programinės įrangos identifikatoriai (1)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
00003E4B01140200003E7D463C05 1.94.004000075D4463C71 BOSCH MG1CS201 (DME_84T1)

ECU pastabos

Micro Infineon Tricore TC298TP Serial protocol enabled ONLY on New Genius, it does not work on Genius To work on this ECU you can use NewTrasdata